Jie Yang

Jie Yang


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 September 2024 in Energies
Verified
Journal Article
Open access
PDF file
BSBinglin Song
Binglin Song
GMGuoying Meng
Guoying Meng
WHWei Huang
Wei Huang
AWAiming Wang
Aiming Wang
XCXiaoHan Cheng
XiaoHan Cheng
JYJie Yang
Jie Yang
Given that two-phase closed thermosiphons (TPCT) are a prevalent and efficacious means of heat transfer. However, non-condensable gas (NCG) may potentially impact the heat transfer performance of the aforementioned devices. Nevertheless, the theoretical analysis of heat transfer in TPCT containing NCG is not fully comprehensive and therefore requires further supplementation by means of relevant experiments. This paper presents the development and experimental investigation of a theoretical heat transfer model for a TPCT containing NCG. The research encompasses the optimal fluid-filling ratio of R22 and R410a working fluid and the impact of NCG on heat transfer in the condenser section of TPCT. Experimental findings indicate that TPCT with R22 and R410a working fluids at a fluid-filling ratio of 60% and 50%, respectively, demonstrate excellent isotherm and heat transfer efficiency. The presence of NCG affects the condenser section heat transfer process of the vapor, leading to a 2 °C decrease in the average temperature of the condenser section of the TPCT (Tca). In comparison with the TPCT without NCG, it was observed that an increase in the mass of NCG from 0.0097 to 0.0197 mol resulted in a reduction in the effective length of the condenser section (La) and effective heat transfer rate (κ) of R22 TPCT. The decrease in La was 75.1 mm, while the decrease in κ was 15.02%. Furthermore, at the same NCG mass, the effective heat transfer rate of R410a TPCT is evidently superior to that of R22 TPCT. The NCG in the TPCT can be removed by using a check valve. Nevertheless, this will result in a reduction in the fluid-filling ratio of the TPCT. The temperature of the R410a TPCT containing 0.0197 mol NCG with a fluid-filling ratio of 50% is comparable to that observed in fluid-filling ratio of 40% after the NCG is exhausted.

12 November 2025 in Energies
Verified
Journal Article
Open access
PDF file
BSBinglin Song
Binglin Song
GMGuoying Meng
Guoying Meng
AWAiming Wang
Aiming Wang
XCXiaoHan Cheng
XiaoHan Cheng
JYJie Yang
Jie Yang
In order to ensure the stability of the gravity heat pipe (GHP) heat exchanger in the mine return air waste heat recovery project and to explore the influence of the working fluid and filling ratio of the GHP on the heat transfer performance, this paper establishes a computational fluid dynamics (CFD) model of the GHP for mine return air waste heat recovery. The heat transfer characteristics and multiphase flow mechanism of the GHP with R22 and R410a working fluids at 30% to 80% filling ratios were studied using the VOF model from three aspects: two-phase flow, wall temperature, and thermal resistance. The validity of the model was verified through experimental data. The findings of the research indicate that the physical property parameters of the working fluid and the alterations in the filling ratio exert a substantial influence on the liquid-phase boiling heat transfer and the condensation process on the condenser wall. The CFD operation results demonstrate a high degree of congruence with the experimental data. The maximum deviation in the wall temperature is 2.9%. When the filling ratio is in the range of 50% to 60%, the axial distribution of the wall temperature tends to be flat. With regard to thermal resistance, both CFD and experimental results demonstrate a tendency of initially decreasing and subsequently increasing with increasing filling ratio. The average wall temperature of R410a GHP with a 50% filling ratio reached the highest value (20.3 °C), and the thermal resistance reached the lowest value (0.021 K/W), demonstrating superior heat transfer performance and excellent isothermal characteristics.

16 July 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
SSShimin Shu
Shimin Shu
MXMuchen Xu
Muchen Xu
PLPeifeng Liu
Peifeng Liu
PYPeize Yang
Peize Yang
TWTianyi Wu
Tianyi Wu
JYJie Yang
Jie Yang
Fault diagnosis methods based on deep learning have been widely applied to bearing fault diagnosis. However, current methods usually diagnose on the same individual device, which cannot guarantee reliability in real industrial scenarios, especially for new individual devices. This article explores a practical cross-individual scenario and proposes a Kolmogorov–Arnold enhanced convolutional transformer (KACFormer) model to improve both general feature representation and cross-individual capabilities. Specifically, the Kolmogorov–Arnold representation theorem is embedded into convolution and multi-head attention mechanisms to develop novel Kolmogorov–Arnold enhanced convolution (KAConv) and Kolmogorov–Arnold enhanced attention (KAA). The adaptive activation function enhances its nonlinear modeling ability. Comprehensive experiments are performed on two public datasets, demonstrating the superior generalization of the proposed KACFormer model with a higher accuracy of 95.73% and 91.58% compared to existing advanced models.

21 January 2026 in Sensors
Verified
Journal Article
Open access
PDF file
XFXuewen Feng
Xuewen Feng
AWAiming Wang
Aiming Wang
GMGuoying Meng
Guoying Meng
YXYiyang Xu
Yiyang Xu
JYJie Yang
Jie Yang
JWJuntao Wang
Juntao Wang
Semantic segmentation of workpieces and die cavities is critical for intelligent process monitoring and quality control in hammer die-forging. However, the field of 3D point cloud segmentation currently faces prominent limitations in forging scenario adaptation: existing state-of-the-art (SOTA) methods are predominantly optimized for road driving or indoor scenes, where targets have stable poses and regular surfaces. They lack dedicated designs for capturing the fine-grained deformation characteristics of forging workpieces and alleviating multi-scale feature misalignment caused by large pose variations—key pain points in forging segmentation. Consequently, these methods fail to balance segmentation accuracy and real-time efficiency required for practical forging applications. To address this gap, this paper proposes a novel semantic segmentation framework fusing 3D point cloud and bird’s-eye-view (BEV) representations for complex die-forging scenes. Specifically, a Star-based encoding module is designed in the BEV encoding stage to enhance capture of fine-grained workpiece deformation characteristics. A hierarchical feature-offset alignment mechanism is developed in decoding to alleviate multi-scale spatial and semantic misalignment, facilitating efficient cross-layer fusion. Additionally, a weighted adaptive fusion module enables complementary information interaction between point cloud and BEV modalities to improve precision.We evaluate the proposed method on our self-constructed simulated and real die-forging point cloud datasets. The results show that when trained solely on simulated data and tested directly in real-world scenarios, our method achieves an mIoU that surpasses RPVNet by 1.1%. After fine-tuning with a small amount of real data, the mIoU further improves by 5%, reaching optimal performance.