Venkata Ratnam Ratnam Myneni

Dr. Venkata Ratnam Ratnam Myneni

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2022 in International Journal of Chemical Engineering
Verified
Journal Article
Open access
PDF file
NHNasim Hasan
Nasim Hasan
VMVenkata Ratnam Ratnam Myneni
Venkata Ratnam Ratnam Myneni
Biodiesel is marketed as a long‐term renewable fuel that may partially replace fossil fuels in transportation while also helping to reduce global warming. The current study is focused on using waste animal fat as a feedstock for biodiesel production. Sulfuric acid (H 2 SO 4 ) and potassium hydroxide (KOH) are used as catalysts, with methanol as an alcohol. Temperature at 60°C, reaction time 2 hrs for acid catalyst, and 55°C, reaction time 90 min for base catalyst with a methanol to oil ratio of 5 : 1 are the experimental and optimized process conditions. With the H 2 SO 4 catalyst, the biodiesel yield was 65.7%, while with the KOH catalyst, it was 48.8%. The ASTM standards are used to compare and study the physicochemical characteristics. This study offers an environmentally friendly solution to a global problem of atmospheric pollution, and at the same time, it shows a commercial alternative to reduce the ecological impact caused by waste animal fat.

1 January 2020 in Materials Today: Proceedings
Verified
Journal Article
Closed access
VMVenkata Ratnam Ratnam Myneni
Venkata Ratnam Ratnam Myneni
CKC. Karthikeyan
C. Karthikeyan
KRK. Nagamalleswara Rao
K. Nagamalleswara Rao
VMV. Meena
V. Meena

26 March 2022 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
MPMurugesan Manikkampatti Palanisamy
Murugesan Manikkampatti Palanisamy
VMVenkata Ratnam Ratnam Myneni
Venkata Ratnam Ratnam Myneni
BGBadhane Gudeta
Badhane Gudeta
SKSrikanth Komarabathina
Srikanth Komarabathina
The rapid advancement of technical advancements has resulted in the generation of substantial amount of electronic trash (e-waste). The volume of e-waste created, as well as the presence of both dangerous and beneficial elements, enhances the business potential of recovery and recycling significantly. Waste printed circuit boards (PCBs) include a number of hazardous heavy metals, including copper (Cu), tin (Sn), lead (Pb), and others (Zn, Ni, Fe, Br, Mn, Mg etc.). These discarded metals without treatment threaten the economy, the environment, and human health. Heavy metal recovery from PCBs is a big difficulty for researchers. The present review focuses on technological advances in the recovery of toxic, precious metals from PCBs.

8 November 2021 in International Journal of Chemical Engineering
Verified
Journal Article
Open access
PDF file
BGBadhane Gudeta
Badhane Gudeta
SKSolomon K
Solomon K
VMVenkata Ratnam Ratnam Myneni
Venkata Ratnam Ratnam Myneni
Tobacco, one of the most significant nonfood crops, is critical to agriculture worldwide. The tobacco processing business creates a significant amount of hazardous tobacco waste containing nicotine, and only a tiny portion of it gets recycled. Nicotine, the primary component of tobacco products such as cigarettes, is an alkaloid and can be used as an insecticide. This research aims to extract nicotine from discarded cigarette butts and utilize it as an insecticide. Extraction, emulsification, and efficiency testing on cabbage aphids are all part of the procedure. The initial extraction tests used a solvent combination of ethanol and methanol in various ratios, with a 3:1 ratio yielding the best results. Temperature (3060°C), extraction length (46hrs), and sodium hydroxide concentration (13M) are the independent variables studied for extraction parameters, and the optimal conditions are determined using Design-Expert, response surface approach central composite design (RSM-CCD). In addition, artificial neural network (ANN) studies with MATLAB were used to accurately forecast extraction yield. The extracted product was evaluated using a gas chromatographymass spectrometry (GC-MS) and a UV/visible spectrophotometer. The ideal crude extract yield and nicotine content were 17.75 and 3.26, respectively, at the optimal conditions of temperature 60°C, time 4hrs, and NaOH concentration 2.83M with desirability of 0.832. The nicotine extracted was emulsified by combining the crude extract with a combination of palm oil and surfactants. Density, viscosity, pH, flash point, and surface tension of the emulsified concentration were measured and reported as 1.01±0.01g/ml, 585.33±2.52mPa s, 9.37±0.03, 87.96C, and 34.10mN/m, respectively. On the cabbage aphid, the emulsified concentrated extract performed best at a ratio of 1:100 (emulsified concentrated to solvent).

1 January 2023 in Adsorption Science & Technology
Verified
Journal Article
Open access
PDF file
VMVenkata Ratnam Ratnam Myneni
Venkata Ratnam Ratnam Myneni
PAP. Akilamudhan
P. Akilamudhan
KKK. Senthil Kumar
K. Senthil Kumar
SRS. Narasimha Reddy
S. Narasimha Reddy
NKNAGAMALLESWARARAO KANIDARAPU
NAGAMALLESWARARAO KANIDARAPU
RDReddy Prasad D.M.
Reddy Prasad D.M.
Emerging contaminants (ECs) are substances that have been detected in water but have not been thoroughly tested or regulated. Pesticides, cosmetics, pharmaceuticals, and other medications are examples of compounds in this category. Even at low quantities, these pollutants can harm human health and the environment; therefore, avoiding them is critical. The consequences of EC pollution on the endocrine, hormonal, and genetic systems are causing significant concern. Even with current best practices and available technology, it is difficult to totally eliminate ECs from municipal and industrial wastewater treatment plants. Adsorption has been the method of choice for EC removal since it is less costly, more effective, and easier to use. To treat ECs, newer generation nanoadsorbents are employed. Adsorption was greatly enhanced by functional changes to the adsorbent surface. Carbon nanostructures are widely used as adsorbents because of their outstanding surface properties, adaptability, large surface area, adjustable structural changes, and high chemical stability. This review reviews and examines recent research on the production and use of carbon-based nanoadsorbents. The emphasis is on carbon nanotubes, graphene, and graphene-derived adsorbents. It is being investigated if these adsorbents can be used to extract hormone-disrupting chemicals and other emerging pollutants. The sources and classification of these pollutants, treatment knowledge gaps, and novel prospects for increasing carbonaceous nanoadsorbent utilization were all explored. The environmental and health problems associated with EC use are also studied.

29 April 2023 in International Journal of Chemical Engineering
Verified
Journal Article
Open access
PDF file
BSBandela Sowjanya
Bandela Sowjanya
PKPulipati King
Pulipati King
MVMeena Vangalapati
Meena Vangalapati
VMVenkata Ratnam Ratnam Myneni
Venkata Ratnam Ratnam Myneni
The goal of this research was to employ copper-doped zinc oxide nanoparticles (Cu/ZnONPs) as an adsorbent to remove the potentially toxic azo dye Congo red (CR). The Cu/ZnONPs were made using a chemical coprecipitation method, and their characteristics were examined using XRD, SEM, EDS, and FTIR methods. The response surface methodology (RSM) central composite design (CCD) is used to optimize the operational parameters agitation time, adsorbent dosage, solution pH, and initial concentration of CR solution during the adsorption process. The agitation period of 29.48min, the Cu/ZnONP dosage of 0.301g/L, the solution pH of 6.96, and the CR initial concentration of 90mg/L resulted in a maximum CR adsorption of 94.14 and a desirability of 0.976. The kinetic findings fit the pseudo-second-order kinetic equation, and the equilibrium data agreed with the Langmuir isotherm (maximum uptake capacity qmax=250mg/g). During the thermodynamic experiments, endothermic, spontaneous, and physical adsorptions were observed.