A folding wing morphing aircraft should complete the folding and unfolding process of its wings while in flight. Calculating the hinge moments during the morphing process is a critical aspect of a folding wing design. Most previous studies on this problem have adopted steady-state or quasi-steady-state methods, which do not simulate the free-flying morphing process. In this study, we construct an aeroelastic flight simulation platform based on the secondary development of ADAMS software to simulate the flight-folding process of a folding wing aircraft. A flexible multibody dynamic model of the folding wing structure is established in ADAMS using modal neutral files, and the doublet lattice method is developed to generate aerodynamic influence coefficient matrices that are suitable for the flight-folding process. The user subroutine is utilized, aerodynamic loading is realized in ADAMS, and an aeroelastic flight simulation platform of a folding wing aircraft is built. On the basis of this platform, the flight-folding process of the aircraft is simulated, the hinge moments of the folding wings are calculated, and the influences of the folding rate and the aircraft’s center of gravity (c.g.) position on the results are investigated. Results show that the steady-state method is applicable to the slow folding process. For the fast folding process, the steady-state simulation errors of the hinge moments are substantially large, and a transient method is required to simulate the flight-folding process. In addition, the c.g. position considerably affects the hinge moments during the folding process. Given that the c.g. position moves aft, the maximum hinge moments of the inner and outer wings constantly increase.
This paper focuses on the nonlinear aeroelastic system identification method based on an artificial neural network (ANN) that uses time-delay and feedback elements. A typical two-dimensional wing section with control surface is modelled to illustrate the proposed identification algorithm. The response of the system, which applies a sine-chirp input signal on the control surface, is computed by time-marching-integration. A time-delay recurrent neural network (TDRNN) is employed and trained to predict the pitch angle of the system. The chirp and sine excitation signals are used to verify the identified system. Estimation results of the trained neural network are compared with numerical simulation values. Two types of structural nonlinearity are studied, cubic-spring and friction. The results indicate that the TDRNN can approach the nonlinear aeroelastic system exactly.
In this paper, an improved short memory principle based on the Grünwald–Letnikov definition is proposed and applied in solving fractional vibration differential equations. The improved idea is to adjust the truncation of memory time in short memory principle (SMP) to the truncation of binomial coefficient terms, and the finite coefficients are repeatedly applied to the step size gradually enlarged. In this method, a very small initial step size is used to meet the accuracy requirements, and then the step size is gradually enlarged to prolong the memory time and reduce the amount of calculation. Examples of free vibration, forced vibration with a single-degree-of-freedom and a vehicle suspension two-degree-of-freedom vibration reduction model verify the method’s accuracy and effectiveness.
22 February 2022 in International Journal of Aerospace Engineering
A folding wing aircraft can autonomously change its configuration in flight to respond to different flying environments. Hinge moment during morphing process is an important basis for driving mechanism design and structural strength check, and its calculation depends on the simulation of the morphing process. Existing studies mostly use the simplified lifting surface method for aerodynamic modeling. In this paper, the CFD-based simulation method is studied, and the results are compared with those by the lifting surface method. First, the unsteady aerodynamic modeling method of the folding wing based on the CFD method is studied, an effective description method is given to define the wall mesh motion caused by wing folding and aileron deflection, and an unfolding–refolding strategy is proposed to improve the quality of the internal mesh in the case of large folding angles. Then, the CFD aerodynamic model is coupled through a developed coupling calculation program with the flexible multibody structure model for the simulation of a flight-morphing process. The comparison with the results of the lifting surface method shows that hinge moments obtained according to the two aerodynamic models are markedly different. Analysis of the difference shows that airfoil thickness considerably affects aerodynamic loading distributions and hinge moments of folding wing aircraft. The lifting surface method ignores airfoil thickness, which will cause large simulation errors in hinge moments.
28 February 2007 in Journal of the Faculty of Agriculture, Kyushu University
For the high-aspect-ratio composite joined-wing UAV, as the geometric nonlinear significant effect, nonlinear aeroelastic analysis method should be applied when study its aeroelastic tailoring method. In the paper, based on the secondary development of MSC/Nastran software with Direct matrix abstraction programme language, with the adopting the multidisciplinary design optimization platform Isight software integrating the MSC/Nastran software analysis, modules of the static aeroelastic analysis, nonlinear static analysis and flutter analysis, a nonlinear aeroelastic tailoring method for high –aspect-ratio composite joined-wing UAV has been presented. Example show that, the method proposed in this paper not only can solve nonlinear aeroelastic tailoring of high-aspect-ratio composite joined-wing UAV problem, but also can be applied to complex engineering structure.