Aggregates are a significant component of pervious concrete. Pervious concrete using iron tailings as coarse aggregates was prepared to study the feasibility of this approach. A mix design procedure was also used to design pervious concrete based on different target porosities. The effective porosity, measured porosity, dry density, compressive strength, and permeability coefficient of pervious concrete were studied. The results show that the mix design procedure based on a target porosity is relatively reasonable for designing iron tailing-based pervious concrete. The 28 d compressive strength of the pervious concrete decreased from 42 to 11 MPa as the effective porosity increased from 5.2% to 27.2%. The effective porosity of the equilibrium point of the compressive strength and permeability coefficient of pervious concrete was approximately 16%, where the compressive strength was 21.5 MPa, and the water permeability was 3.2 mm/s. The permeability coefficient of pervious concrete can be predicted as an exponential function of the effective porosity, and the compressive strength of pervious concrete can be predicted as a logarithmic function of the effective porosity.

In this paper, a simple and efficient fractal-based approach is presented for capturing the effects of initial void ratio on the soil-water characteristic curve (SWCC) in a deformable unsaturated soil. In terms of testing results, the SWCCs (expressed by gravimetric water content) of the unsaturated soils at different initial void ratios were found to be mainly controlled by the air-entry value (Ψ_a), while the fractal dimension (D) could be assumed to be constant. As a result, in contrast to the complexity of existing models, a simple and efficient model with only two parameters (i.e., D and Ψ_a) was established for predicting the SWCC considering the effects of initial void ratio. The procedure for determining the model parameters with clear physical meaning were then elaborated. The applicability and accuracy of the proposed model were well demonstrated by comparing its predictions with four sets of independent experimental data from the tests conducted in current work, as well as the literature on a wide range of soils, including Wuhan Clay, Hefei and Guangxi expansive soil, Saskatchewan silt, and loess. Good agreements were obtained between the experimental data and the model predictions in all of the cases considered.

Building structures are prone to cracking, leakage, and corrosion under complex loads and harsh marine environments, which seriously affect their durability performance. To design cementitious composites with excellent mechanical and impermeability properties, Engineered Cementitious Composites (ECCs) doped with ultrahigh molecular weight polyethylene short-cut fibers (PE-ECCs) were used as the reference group. Different types (XYPEX-type from Canada, SY1000-type from China) and doses (0%, 0.5%, 1.0%, 1.5%, 2.0%) of Cementitious Capillary Crystalline Waterproofing materials (CCCWs) were incorporated. The effect of CCCWs on the mechanical and impermeability properties of PE-ECCs, and the microscopic changes, were investigated to determine the best type of CCCW to use and the best amount of doping. The results showed that with increasing the CCCW dosage, the effects of both CCCWs on the mechanical and impermeability properties of PE-ECC increased and then decreased, and that the best mechanical and impermeability properties of PE-ECC were achieved when the CCCW dosing was 1.0%. The mechanical properties of the PE-ECC were more obviously improved by XYPEX-type CCCW, with a compressive strength of 53.8 MPa, flexural strength of 11.8 MPa, an ultimate tensile stress of 5.56 MPa, and an ultimate tensile strain of 7.53 MPa, which were 37.95%, 53.25%, 14.17%, and 21.65% higher than those of the reference group, respectively. The effects of the two CCCWs on impermeability were comparable. CCCW-PE-ECC(X1.0%) and CCCW-PE-ECC(S1.0%) showed the smallest permeation heights, 2.6 mm and 2.8 mm, respectively. The chloride ion diffusion coefficients of CCCW-PE-ECC(X1.0%) and CCCW-PE-ECC(S1.0%) exhibited the smallest values, 0.15 × 10⁻¹² m²/s and 0.10 × 10⁻¹² m²/s, respectively. Micromorphological tests showed that the particle size of the XYPEX-type CCCW was finer, and the intensity of the diffraction peaks of C-S-H and CaCO₃ of PE-ECC increased after doping with two suitable doping amounts of CCCW. The pore structure was improved, the surface of the matrix was smoother, and the degree of erosion of hydration products on the fiber surface was reduced after chloride ion penetration. XYPEX-type CCCW demonstrated a more obvious improvement in the PE-ECC pore structure.