During the past 50 years, the aim to reduce the eddy current losses in magnetic cores to a minimum led to the formulation of new materials starting from electrically insulated iron powders, today called Soft Magnetic Composites (SMC). Nowadays, this promising branch of materials is still held back by the mandatory tradeoff between energetic, electrical, magnetic, and mechanical performances. In most cases, the research activity focuses on the deposition of an insulating/binding layer, being one of the critical points in optimizing the final composite. This insulation usually is achieved by either inorganic or organic layer constituents. The main difference is the temperature limit since most inorganic materials typically withstand higher treatment temperatures. As a result, the literature shows many materials and process approaches, each one designed to meet a specific application. The present work summarizes the recent advances in state of the art, analyzing the relationship among material compositions and magnetic and mechanical properties. Each coating shows its own processing sets, which vary from simple mechanical mixing to advanced chemical methods to metallurgical treatments. From state of the art, Aluminum coatings are characterized by higher current losses and low mechanical properties. In contrast, higher mechanical properties are obtained by adopting Silicon coatings. The phosphates coatings show the best-balanced overall properties. Each coating type was thoroughly investigated and then compared with the literature background highlighting. The present paper thus represents a critical overview of the topic that could serve as a starting point for the design and development of new and high-performing coating solutions for SMCs. However, global research activity continuously refines the recipes, introducing new layer materials. The following steps and advances will determine whetherthese materials breakthrough in the market.

In the last years, functionalized powders are becoming of increasing interest in additive manufacturing (particularly in laser powder bed fusion processing, L-PBF), due to their improved flowability and enhanced processability, particularly in terms of laser absorbance. Functionalized powders may also provide higher final mechanical or physical properties in the manufactured parts, like an increased hardness, a higher tensile strength, and density levels close to theoretical. Coatings represent a possible interesting approach for powders’ functionalizing. Different coating methods have been studied in the past years, either mechanical or non-mechanical. This work aims to present an overview of the currently obtained coated powders, analyzing in detail the processes adopted for their production, the processability of the coated systems, and the mechanical and physical properties of the final parts obtained by using L-PBF for the powders processing.

Additive manufacturing is a key enabling technology in the manufacture of highly complex shapes, having very few geometric limitations compared to traditional manufacturing processes. The present paper aims at investigating mechanical properties at cryogenic temperatures for a 316L austenitic stainless steel, due to the wide possible cryogenic applications such as liquid gas confinement or superconductors. The starting powders have been processed by laser powder bed fusion (LPBF) and tested in the as-built conditions and after stress relieving treatments. Mechanical properties at 298, 77 and 4.2 K from tensile testing are presented together with fracture surfaces investigated by field emission scanning electron microscopy. The results show that high tensile strength at cryogenic temperature is characteristic for all samples, with ultimate tensile strength as high as 1246 MPa at 4.2 K and 55% maximum total elongation at 77 K. This study can constitute a solid basis for investigating 316L components by LPBF for specific applications in cryogenic conditions.

Additive manufacturing, including laser powder bed fusion, offers possibilities for the production of materials with properties comparable to conventional technologies. The main aim of this paper is to describe the specific microstructure of 316L stainless steel prepared using additive manufacturing. The as-built state and the material after heat treatment (solution annealing at 1050 °C and 60 min soaking time, followed by artificial aging at 700 °C and 3000 min soaking time) were analyzed. A static tensile test at ambient temperature, 77 K, and 8 K was performed to evaluate the mechanical properties. The characteristics of the specific microstructure were examined using optical microscopy, scanning electron microscopy, and transmission electron microscopy. The stainless steel 316L prepared using laser powder bed fusion consisted of a hierarchical austenitic microstructure, with a grain size of 25 µm as-built up to 35 µm after heat treatment. The grains predominantly contained fine 300–700 nm subgrains with a cellular structure. It was concluded that after the selected heat treatment there was a significant reduction in dislocations. An increase in precipitates was observed after heat treatment, from the original amount of approximately 20 nm to 150 nm.

A new technology may be proposed for the realization of the magnetic parts of electromechanical devices, mainly for small electric machines. Such a technology provides the substitution of the traditional magnetic sheets with parts obtained by molding special magnetic powders [soft magnetic composites (SMC)]. The advantages may be constituted not only by economical reasons, but mostly by the possibility to realize parts having shapes otherwise impossible with the traditional lamination. Some commercial products are available in the market as “ready to press” powders, but their mechanical properties are in general not sufficient. To investigate the possibility to obtain good mechanical properties maintaining the magnetic characteristics of a selected commercial insulated iron powder compound, the authors have conducted a research activity based on the use of special iron powders and a selected epoxy resin as binder. The paper describes the activity carried out for the realization of SMC by mixing iron powders and Epoxy resin with different binder percentages and molding pressures. The obtained results have to be considered very satisfactory and suggest to continue the research argument to explore the possibilities of further improvements.