This article is a study of Hydrotreated Vegetable Oil and Butanol Fuel blends, which are mixed in three different proportions (HVOB5, HVOB10 and HVOB20), and the comparison of their combustion (in-cylinder pressure, pressure rise and ROHR), performance (fuel consumption, BSFC and BTE) and emission (CO2, NOX, HC and Smoke) characteristics with those of fossil diesel fuel. In the wake of finding an alternative fuel that requires little to zero modifications to the existing IC engines, it is necessary to account for the necessity of matching the efficiency of conventional fuels as well as greatly reducing its exhaust emissions. As a result of transesterification, HVO is found to have better stability and higher CN compared to other biofuels. It is termed a “renewable diesel” due to its ability to reduce emissions while maintaining efficiency. HVO as a fuel has higher cost efficiency, and for a more stable oxygen content in the fuel, an alcohol substitute is needed. Butanol, which has a considerable advantage over other alcohols due to its higher density, viscosity and CN, is selected. HVOB5 and HVOB10 are found to match diesel fuel in terms of fuel consumption while having a ~1% lesser efficiency. In terms of emissions, all the fuel mixtures including HVO100 are found to have ~4–5% lesser CO2, ~10–15% lesser NOX and a ~25–45% reduction in smoke levels.
17 December 2024 in Facta Universitatis, Series: Mechanical Engineering
Air pollution, especially from particulate matter (PM), is a significant environmental and health issue worldwide. This research examines the use of acoustic agglomeration (AA) as a novel technique to diminish fine particle emissions, concentrating on the influence of frequency on particle characteristics and agglomeration duration. This study aims to improve the effectiveness of traditional filtration systems by investigating acoustic wave-induced particle agglomeration as an alternative method. The research integrates experimental and computational methodologies. Emissions from a 1.9 turbocharged 4-cylinder diesel engine using FAT80IP20 fuel were subjected to analysis in a custom-designed acoustic chamber. Frequencies of 21.2 kHz and 34.6 kHz were used, with particle measurements recorded using a Fluke 985 particle counter. Computational simulations using the Discrete Element Method (DEM) were performed to examine particle behaviour at different acoustic frequencies, accounting for first-order factors such orthokinetic interactions and acoustic wake effects. Results demonstrate that elevated frequencies (34.6 kHz) accelerate particle agglomeration, although the overall quantity of agglomerated particles diminishes. Experimental results indicated a 62.78% decrease in 5 μm particles and a 300% rise in 10 μm particles at 34.6 kHz. The findings correspond with the computer calculations, which indicated that heightened frequency enhances particle mobility and collisions while diminishing the likelihood of prolonged agglomeration inside the chamber confines. The results confirm the efficacy of acoustic agglomeration for emission control, emphasising a frequency-dependent trade-off between agglomeration speed and the volume of agglomerated particles. This study advances the development of sophisticated filtering technologies and more environmentally friendly transportation alternatives.
To achieve the goal of climate neutrality set by the European Union, it is important to find an efficient strategy to simultaneously lower nitrogen oxide, carbon monoxide, and particle emissions. When a portion of exhaust gas is reintroduced back into the combustion chamber, it reduces the combustion temperature. This reduces NOX emissions but has a negative impact on CO and particle emissions due to the lower concentration of O2. Reducing the combustion temperature can also indirectly influence particle formation. By including an oxygen-rich alternative fuel, CO emissions are reduced by 28% and 33% at 60 and 90 Nm, respectively. To further reduce particle emissions, which have significant health risks, acoustic waves are introduced to achieve better filtration through conventional DPFs that filter particles with larger diameters. With 21 kHz of acoustic frequency and 0% EGR, a 6% increase in large particles is observed. With moderate rise in the recirculation percentage, a higher combined efficiency of EGR and acoustic waves is observed. With 21 kHz acoustic frequency and 10% EGR, a 73% increase in larger particles is observed at lower loads and a 32% increase at higher loads is observed. Simultaneous emission reduction can be achieved by combining the benefits of using oxygen-rich fuel, acoustics, and EGR at a moderate rate.
The particle emissions from diesel engines are a major environmental problem due to their harmful effects on air quality and human health. This article investigates the underlying acoustic parameters that determine the efficiency of reducing the fine particles through agglomeration. The impact of a change in frequency and voltage on the acoustic waves through the excitation source is researched and analyzed. Three blends of rapeseed methyl ester and isopropanol (RME95I5, RME90I10, and RME80I20) are used for experiments to study the combined benefit of oxygen-rich blends. The exhaust particles are measured before and after the exposure to acoustic waves operated at a varying voltage and frequency ranges. The fine particle reduction with a simultaneous increase in 5–10 µm particles is found to be better at the lower frequency due to the severe acoustic attenuation at the higher frequency. With the increase in voltage to 200 V, the reduction in fine particles and the simultaneous increase in coarse particles are comparatively less. The change in voltage induces an increase in sound intensity, which slows down the growth of agglomerates. The study presents the critical information necessary to use acoustic waves to reduce particle pollution using conventional filters, including the mechanisms by which sound intensity affects particle size distribution and the effectiveness of this method in various environmental conditions.
Road transport in the European Union is responsible for approximately 60% of PM10 emissions and 45% of PM2.5 emissions. Acoustic agglomeration is researched to be the most effective after-treatment method to control particle pollution. Recent experimental research suggests that at a frequency of around 20 kHz and a sound pressure level of 140 dB, particles can be agglomerated. The kinetic energy of the particles is influenced by the presence of acoustics, and this enhances the collision efficiency between the particles. These collided fine particles increase in size and can be easily filtered through conventional filters. Additionally, clean burning biofuels produce comparatively fewer particles; hence RME is used for experiments along with its two blends of isopropanol (RME95I5 and RME90I10). The results are then compared to those of standard diesel fuel. With an increase in load, an average reduction of 20% in fine particles is observed along with an increase in large-sized particles. The aggregation of smaller particles is observed in a range of 0–50% in almost all tested conditions. With the increase in isopropanol from 5 to 10%, oxygen content in the fuel increased by 7%, a 1% reduction in carbon and a 2% reduction in C/H ratio is observed which led to a 6 and 9% reduction in particle emissions at 60 Nm and 90 Nm, respectively. At higher loads, D100, RME95I5 and RME90I10 recorded an agglomeration of 10%, 111% and 189%, respectively. Similar results are observed for the tendency for agglomeration at lower loads.