In recent years, the market scale of new energy sources has progressively expanded, with a significant volume of new energy components (such as photovoltaic panels, wind turbine blades, and lithium batteries) entering their end-of-life phase. Disposal through mechanical shredding and landfill alone not only constitutes a waste of resources but also imposes substantial environmental pressures. Consequently, the efficient and environmentally sound recycling of end-of-life new energy components has become pivotal to the sustainable development of the new energy industry. Microwave heating technology, with its unique advantages including selective heating and rapid temperature rise rates, offers a highly promising solution for the resource recovery of end-of-life new energy components. This paper reviews research progress in applying microwave technology to the recycling of photovoltaic modules, wind turbine blades, and lithium batteries. It first elucidates the mechanisms governing microwave–material interactions, focusing on the influence of microwave power, processing time, and additives. Finally, it examines the challenges facing the large-scale application of microwave technology in recycling end-of-life renewable energy components, identifies current research limitations, and outlines future prospects for development towards greater efficiency and lower carbon footprints.
Electrocatalytic CO2 reduction reaction (CO2RR) to ethylene (C2H4) has emerged as a promising approach for converting CO2 into valuable chemicals while utilizing renewable electricity. To facilitate the commercialization of this technology, a process-level techno-economic assessment (TEA) is constructed for a plant producing 100 tons/day of C2H4 from coal-power flue gas CO2 using a membrane electrode assembly (MEA) electrolyzer and downstream gas separations. The model integrates (i) flue gas CO2 capture by chemical absorption, (ii) CO2RR to C2H4 with H2 as the only co-product, and (iii) cathode off-gas separation by pressure swing adsorption (PSA) plus anode off-gas CO2 recovery and recycle. A Cu10–Sn catalyst measured in an H-cell is projected to MEA operation by scaling current density by 10×, yielding a “Case Study in This Article” scenario of j = 246 mA·cm−2 and FE(C2H4) = 48.74%. Under this scenario, the total cost is 592.61 thousand USD/day (5926 USD/ton), dominated by electricity (39.8%). Scenario analysis shows that the total cost can decrease to 76,755.0 USD/day (767.6 USD/ton) under a future-outlook case with improved electrolyzer performance and low-cost power, enabling a net profit of 19,945.0 USD/day at an ethylene selling price of 967 USD/ton. Sensitivity analysis identifies FE(C2H4), full-cell voltage, and electricity price as the most influential variables. The results translate laboratory catalyst metrics into industrial cost drivers and clarify quantitative performance targets for commercialization.
Activated carbon has shown good catalytic performance in water treatment, but its wide application is limited by its high price. Activated coke exhibits functional groups and is low-cost. However, there is limited research on activated coke as a catalyst. In our previous study, powdered activated coke (PAC) exhibited good catalytic performance in NH3-N treatment with ozonation. Increasing nitrogen selectivity is the key to harmless degradation of NH3-N, which has received little attention. In this paper, manganese-loaded powdered coke (Mn–PAC) was prepared, aiming to further improve the nitrogen selectivity. Under the same conditions, the PAC/O3 system achieved 92.16% NH3-N removal and 49.46% nitrogen selectivity, while the Mn–PAC/O3 system achieved almost 100% NH3-N removal and 79.31% N2 selectivity. When Mn–PAC was reused for the sixth time, the system achieved about 70% and 46% NH3-N removal and N2 selectivity, both of which were about 10% higher than those of PAC. Complex redox and synergistic interactions existed in the Mn–PAC/O3 system. The Mn–PAC surface contains reactive sites such as C=C, C=O, π–π bonds, ArOH, and various MnOx. These components collectively facilitate ozone decomposition into ·OH, ·O2−, and 1O2. The 1O2 may play a significant role in converting NH3-N to N2.
A series of Cu-MnOx/GF catalytic electrodes, with graphite felt (GF) pretreated via microwave modification as the catalyst carrier, were prepared under various hydrothermal conditions and characterized using X-ray Diffraction (XRD), Scanning Electron Microscope (SEM), X-ray photoelectron spectroscopy (XPS), N2 adsorption–desorption, and Raman spectroscopy. The catalytic oxidation activity of catalytic Cu-MnOx/GF electrodes toward toluene was evaluated in an all-solid-state electrocatalytic device under mild operating conditions. The evaluation results demonstrated that the microwave-modified catalytic electrode exhibited high electrocatalytic activity toward toluene oxidation, with Cu-MnOx/700W-GF exhibiting significantly higher catalytic activity, indicating that an increase in catalyst loading capacity can promote the removal of toluene. Only CO2 and CO were detected, with no other intermediates observed in the reaction process. Moreover, the catalytic effect was significantly affected by the relative humidity. The catalytic oxidation of toluene can be fully realized under a certain humidity, indicating that the conversion of H2O to strongly oxidizing ·OH on the catalytic electrode is a key step in this reaction.