Dynamic response characteristics and antiseismic performance of the structures which were constructed on the super‐deep overburden layer are affected obviously by the seismic motion characteristics of the super‐deep overburden layer foundation. In this paper, the seismic motion characteristics of horizontally stratified super‐deep overburdenIn this paper, the seismic motion characteristics of horizontally stratified super‐deep overburden based on the research results of on‐site in situ tests and indoor material property tests, the horizontal shear layer method that can consider the nonlinear characteristics of dynamic soil deformation and the characteristics of seismic wave propagation in the soil is used to study the characteristics of ground motions of super‐deep and thick overburden level of an earth‐rock dam in China. The influence law of input ground motion characteristics and input ground motion position on seismic response analysis results of overburden ground is studied. Taking the uniform overburden layer model as an example, the coupling influence analysis of soil layer thickness and shear velocity on ground motion response are carried out, and the coupling influence law is proposed. The study shows that the seismic motion propagating characteristics of the earthquake in super‐deep overburden layer is involved, inputting location of the seismic motion affects the results of ground seismic response greatly; super‐deep overburden layer thickness and the soil shear wave velocity on influence law of ground motion characteristics have coupling. When the shear wave velocity of the soil layer is constant, the surface acceleration response has an inflection point with the change of the soil layer thickness; when the thickness of overburden is constant, the surface acceleration response also has an inflection point with the change of shear wave velocity of the soil layer; these inflexion values are influenced by both soil thickness and shear wave velocity.
The compaction rate of gravel soil is usually characterized by the "relative density". In order to calculate the relative density of gravel soil, the relative density property index of soil should be determined firstly, such as the maximum dry density and the minimum dry density. Because of the size and energy limitation of the laboratory test equipment, The maximum dry density of the gravel soils determined in laboratory tests is often much lower than the actual. For the Yulongkashi high earth-rock fill dam in China, the field large-scale relative density tests of original gravel soil was carried out used actual rolling equipment and large relative density bucket, the compaction characteristics of soil was studied, and the relative density characteristics index of soils with different gradation (coarse grain content) were determined. The test results showed that, compared with the general laboratory test results, the maximum dry density of gravel soil determined by field test was much larger; the minimum dry density as well as maximum dry density of gravel soil had the tendency of increasing and then decreasing with the increase of coarse grain content, and there was an optimum coarse grain content for the density of soil.
Constructing a probabilistic assessment method is the primary task and key step in liquefaction research. This paper presents a systematic investigation into liquefaction potential evaluation methods. Through a comparative analysis of three conventional assessment methods, we identify critical limitations in existing approaches regarding accuracy and adaptability. A probabilistic ANN model was developed using field-collected standard penetration test (SPT) data from 311 liquefaction case histories. The model demonstrates superior performance with an overall accuracy of 86.17%, achieving 83.33% and 90.00% recognition rates for liquefied and non-liquefied cases, respectively. Key metrics, including precision (91.84%), recall (83.33%), and F1-score (87.38%), indicate robust discriminative capability. Comparative studies confirm the ANN model’s advantages over traditional methods in terms of prediction reliability and operational practicality. The research outcomes offer significant value for improving current liquefaction hazard assessment protocols in geotechnical engineering practice.
31 March 2026 in Bulletin of Earthquake Engineering
One of the important tasks in sand liquefaction assessment is to evaluate the likelihood of soil liquefaction. However, most liquefaction assessment methods are deterministic for influencing factors and fail to calculate the liquefaction probability by systematically considering the probability distributions of soil factors. Based on field liquefaction investigation cases, probability distribution fitting and a hypothesis test were carried out. For the variables that failed to pass the fitting and test, the kernel density estimation was conducted. Methods for calculating the liquefaction probability using a Monte Carlo simulation with the probability distribution were then proposed. The results indicated that for (N1)60, SM, S, and GM followed a Gaussian distribution, while CL and ML followed a lognormal distribution; for FC, SM and GM followed a lognormal distribution; and for d50, ML and S followed a Gaussian and lognormal distribution, respectively. The other factors’ distribution curves can be calculated by kernel density estimation. It is feasible to calculate the liquefaction probability based on a Monte Carlo simulation of the variable distribution. The result of the liquefaction probability calculation in this case was similar to that of the existing probability model and was consistent with actual observations. Regional sample differences were considered by introducing the normal distribution error term, and the liquefaction probability accuracy could be improved to a certain extent. The liquefaction probability at a specific seismic level or the total probability within a certain period in the future can be calculated with the method proposed in this paper. It provides a data-driven basis for realistically estimating the likelihood of soil liquefaction under seismic loading and contributes to site classification, liquefaction potential zoning, and ground improvements in seismic design decisions. The practical value of seismic hazard mapping and performance-based design in earthquake-prone regions was also demonstrated.
The pressuremeter test (PMT) measures in situ soil properties under the original stress state with minimal disturbance. However, interpreting PMT data for constitutive parameters remains reliant on empirical correlations, and a key challenge is the poorly understood size effect arising from the equipment dimensions. This study aims to systematically quantify such size effects to provide a scientific basis for optimizing the design of laboratory PMTs. A series of 36 PMT simulations were performed using the finite element method (FEM), incorporating the Duncan–Chang E-B hyperbolic model. Six cylindrical soil models of diameters ranging from 0.6 m to 2.4 m were established for both sand and clay, under three overburden pressures (200 kPa, 1000 kPa and 3000 kPa). The radial stress, strain distributions and borehole wall displacement were systematically analyzed. The analysis reveals that the size effect originates from the truncation of the radial strain integration path. In all cases, borehole wall displacement increases with model diameter, characterized by a steep rise for diameters below 1.2 m and a plateau for those above 1.2 m. Although clay produces larger displacements than sand, and higher stress produces larger displacements than lower stress, the identified pattern remains robust. Considering both the displacement–diameter relationship and practical cost constraints, an optimal equipment diameter of 1.2 m is recommended.