Jun Wang

Prof. Jun Wang


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 October 2025 in Agriculture
Verified
Journal Article
Open access
PDF file
Chaosai LiuChaosai Liu
Chaosai Liu
BZBoyi Zhao
Boyi Zhao
HZHao Zhang
Hao Zhang
TSTong Shen
Tong Shen
JWJun Wang
Jun Wang
The distribution of grain particles within a silo influences heat and moisture transfer during stored grain ventilation, leading to grain quality losses. A study on porosity distribution analysis and ventilation tests was conducted in a pilot silo with a height of 3 m, a diameter of 1.5 m, and a conical dome height of 0.85 m. The E-B constitutive model was incorporated into the secondary development of FLAC3D 5.0 to analyze the vertical pressure distribution in the grain bulk. An anisotropic porosity distribution model for the maize bulk was developed, accounting for both vertical pressure and segregation mechanisms. The differences in airflow and heat transfer during ventilation between isotropic and anisotropic porosity distributions were quantified. A nonlinear model was innovatively proposed to predict the temperature front curve (TFC) during ventilation as affected by porosity variation. The results indicate that friction between the maize kernel and the silo wall led to vertical pressure at the center of the bottom that was 10.7% higher than that near the wall. The average surface porosity of the maize bulk was 2.8% higher than at the bottom. This led to a minimum porosity of 0.409 at the center of the silo bottom, due to the combined effect of impact during the loading process and vertical pressure. The numerical simulation demonstrated excellent consistency with the experimental data. At a supply vent air velocity of 0.126 m/s, an increase in the maize bulk height from 0.725 m to 2.9 m resulted in reductions in airflow rate and average relative humidity of 20.3% and 9.67%. The airflow velocity near the wall was 13.4% higher than that in the center, leading to a faster cooling rate in the peripheral region compared to the center of the maize bulk. The airflow velocity based on the isotropic porosity model was higher at the center than that predicted by the anisotropic model, whereas the opposite trend was observed near the wall. The temperature front during ventilation based on the anisotropic porosity model exhibited a concave curve. A nonlinear model was developed to predict this temperature front, showing strong agreement with computational data.

12 March 2025 in Buildings
Verified
Journal Article
Open access
PDF file
LDLingfeng Du
Lingfeng Du
DWDongchang Wu
Dongchang Wu
JWJun Wang
Jun Wang
SWShaowei Wang
Shaowei Wang
BZBoyi Zhao
Boyi Zhao
XTXiufeng Tang
Xiufeng Tang
Ultra-high performance concrete (UHPC), functioning as a next-generation cementitious engineering material, demonstrates marked superiority over conventional concrete in critical performance metrics, with its groundbreaking characteristics primarily manifested through exceptional strength and enhanced durability parameters. To address structural demands for reduced self-weight, material efficiency, and simplified construction processes in large-span durable structures, this study proposes a retard-bonded prestressed UHPC (RBPU) beam combining UHPC with retard-bonded prestressing tendons (RBPTs). Three RBPU beam specimens, with varying reinforcement ratios, underwent flexural testing to quantitatively assess their bending performance characteristics, providing foundational references for design optimization. The test results show that the failure mode of RBPU beams is typical flexural failure, demonstrating good load-bearing capacity and excellent ductility. As the reinforcement ratio increases, the cracking moment (Mcr) is improved to some extent, while the ultimate moment (Mu) and ductility are significantly enhanced. The plastic influence coefficient of the section modulus (γ) in the calculation of the Mcr was revised, and the ultimate moment Mu was subsequently calculated. The comparison demonstrates good agreement between the experimental values and computational results. This study provides both experimental and theoretical references for further in-depth research and practical applications of RBPU beams.

15 March 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
JWJun Wang
Jun Wang
LWLei Wu
Lei Wu
XLXiang Liu
Xiang Liu
MWmingjie wang
mingjie wang
A viaduct is an important structural form in intercity railway networks, and the curved bridge is inevitable in railway line network planning. When the vehicles cross through the curved bridge, the transverse load experienced by the bridge is much larger than that of the straight bridge due to the centrifugal forces. Therefore, in the bridge resonance analysis, in addition to the vertical moving vehicle load, it is also imperative to consider the radial vehicle load. In order to systematically analyze the dynamic impact factor (or dynamic load allowance) and resonance conditions of the curved intercity railway viaduct, a numerical model is developed. The reliability of the proposed model is assessed by comparing it with the existing literature. Taking the curved viaduct of Zhengzhou-Xuchang railway as a case study, the theoretical resonance velocity, dynamic impact factor, and dynamic time-history response under resonance velocity are calculated. The parameters of different spans, curve radius, and speeds are analyzed, and the reasonable ranges of bridge natural vibration frequency are determined.