The flow field, tracer dispersion and uniformity of strands in two designs of four-strand tun-dishes under normal conditions and single-strand blockage conditions are studied by numerical simulation. The casting speed (flow rate) of strands are increasing uniformly or non-uniformly to improve the strand blockage condition. The uniformity of strands of the cases are evaluated by a novel outflow percentage analysis method. The results show that the flow field in the tundish does not change significantly when the single-strand is blocked or the casting flow rate is increased. After blockage of one strand, the consistency of each strand of u-shaped weir tundish is better than that of double-weir tundish. With the uniform increasing of the casting flow rate, the response time of each strand decreases and the outflow percentage increases. However, the uniformity of strands improved slightly in double-weir tundish but decreased in u-shaped tundish. For the double-weir tundish, significantly increasing the casting flow rate of the strand located in the blocked part by a factor of 1.5 and slightly increasing the casting flow rate of the other strands by a factor of 1.25, the consistency of each strand is the best. For the u-shaped weir tundish, the consistency of each strand is improved by non-uniform increasing of the casting flow rate of the strands. The flow rate of the strand located in the blocked part and the other strands is increased by a factor of 1.25, and 1.375 or 1.2 and 1.4 are the optimized cases.

The study focuses on the four-strand tundish as the research object, aiming at the phenomenon of fewer strand casting (stable blockage) and sudden blockage of the tundish in industrial production. Numerical simulation methods are employed to compare the velocity vectors, flow fields, residence time distribution (RTD) curves, and outflow percentage curves under stable blockage and sudden blockage of the tundishes with a double-weir structure, U-shaped weir structure, and U-shaped weir structure with holes in the front. The results indicate that, after sudden blockage of the tundish strands, the flow field transitions from an unstable four-strand flow field to a stable three-strand flow field. Both the double-weir tundish and the U-shaped weir tundish reach a stable state after 200 s, while the U-shaped weir tundish with holes in the front reaches stability after 150 s. Additionally, compared to other structures, the tundish strands of the U-shaped weir with holes in the front are less affected by blockage, showing better consistency among strands and better adaptability under non-standard casting conditions.

A novel right-sidewall gas blowing method is proposed to improve the flow behavior in a single-strand tundish. Despite advances in tundish flow control, the impact of slag layers and sidewall gas injection on flow dynamics and tracer transport remains underexplored. This study combines 1:3.57 scale water model experiments and Compuational Fluid Dynamics (CFD) simulations to investigate the effects of gas injection heights (50 mm and 100 mm) on flow structure, mixing efficiency, and slag layer interactions. Particle Image Velocimetry (PIV) and the stimulus-response method are used for quantitative validation. Results show that sidewall gas blowing suppresses short-circuit flow, increases average residence time by up to 37%, and reduces dead zone volume by up to 19%. The 50 mm blowing height induces stronger surface turbulence, while the 100 mm height improves flow uniformity. The presence of a slag layer significantly dampens surface fluctuations and alters vortex formation. These findings fill a critical research gap in tundish metallurgy and offer a practical reference for optimizing gas blowing strategies in industrial applications.

In continuous casting, fewer strand operations are sometimes required to match production schedules. However, the study of flow behavior and temperature distribution under fewer strand casting conditions remains insufficiently systematic, especially with regard to the grade casting process, which has not yet been explored. This study presents an innovative investigation of the grade transition process in a symmetrical 12-strand tundish under fewer strand casting conditions. Seven operational cases were analyzed: standard casting (the normal symmetric Case 0), individual closure of strands 1–6 (the asymmetric Cases 1–6), and simultaneous closure of strands 1–2 (the asymmetric Case 7). Notably, strand closures in Cases 5 and 6 significantly impair flow characteristics in their respective strands. The impact area temperature reaches approximately 1844 K (new heat) after 30 min of continuous casting. However, Case 6 exhibits persistent low-temperature regions near strands 5 and 6. The average transition billet lengths for Cases 0 to 7 are 72.41 m, 70.16 m, 70.30 m, 71.68 m, 72.95 m, 72.12 m, 76.35 m, and 65.45 m, respectively. Based on a comprehensive evaluation of flow dynamics, temperature uniformity, and transition billet length, Case 1 emerges as the most favorable single-strand closure strategy. Operational recommendations suggest avoiding strand closure patterns implemented in Cases 5 and 6 during reduced strand casting operations.

During continuous casting, the flow behavior of liquid steel in the tundish directly affects the temperature distribution of liquid steel, inclusion removal, and billet quality. In tundish-related research, water model experiments remain an intuitive method for investigating the flow process in the tundish. However, water model experiments are often conducted in different seasons, and variations in experimental temperature can change fluid properties such as density and viscosity, thereby affecting flow characteristics and the comparability of experimental results. In this study, a 1:3.57 transparent bare single-strand tundish model made of acrylic was used, and the differences in tracer transport processes at 7 °C and 20 °C, as well as the influence of different tracer dosages on the experimental results, were systematically investigated through flow visualization and stimulus-response experiments. The results showed that, under the 7 °C condition, the upward transport tendency of the pure ink tracer was weakened, the overall flow remained closer to the tundish bottom, the transport speed decreased, and the time required to reach the outlet was significantly prolonged. For the saturated KCl solution tracer, a lower temperature enhanced its transport along the bottom toward the outlet and suppressed its diffusion toward the liquid surface. The RTD results showed that, after the temperature was increased, the curves shifted to the left as a whole, and both the peak time and the mean residence time were shortened. The outflow percentage of tracer results showed that the difference for the 10 mL saturated KCl solution between the 7 °C and 20 °C conditions was the most significant. At 7 °C, the total outflow percentage of the 10 mL salt solution tracer at 1500 s was 76.86%, which was 22.97% lower than that at 20 °C. As the tracer dosage increased, the differences in the transport process, RTD curves, and outflow percentage curves under different temperature conditions gradually decreased, indicating that the effect of dosage on the experimental results gradually became stronger than that of temperature. These results indicate that the combined effects of experimental temperature and tracer dosage cannot be neglected in tundish water model experiments.