Amorphous silicon carbide (a-SiC) films are promising solution for functional coatings intended for harsh environment due to their superior combination of physical and chemical properties and high temperature stability. However, the structural applications are limited by its brittleness. The possible solution may be an introduction of nitrogen atoms into the SiC structure. The effect of structure and composition on tribo-mechanical properties of magnetron-sputtered a-SiC_xN_y thin films with various nitrogen content (0–40 at.%) and C/Si close to one deposited on silicon substrates were evaluated before and after exposure to high temperatures up to 1100 °C in air and vacuum. IR transmission spectroscopy revealed formation of multiple C-N bonds for the films with N content higher than 30 at.%. Improvement of the organization in the carbon phase with the increase of nitrogen content in the a-SiCN films was detected by Raman spectroscopy. Nanoindentation and scratch test point out on the beneficial effect of the nitrogen doping on the tribo-mechanical performance of a-SiC_xN_y coatings, especially for the annealed coatings. The improved fracture resistance of the SiCN films stems from the formation of triple C≡N bonds for the as deposited films and also by suppression of SiC clusters crystallization by incorporation of nitrogen atoms for annealed films. This together with higher susceptibility to oxidation of a-SiCN films impart them higher scratch and wear resistance in comparison to SiC films before as well as after the thermal exposure. The best tribo-mechanical performance in term of high hardness and sufficient level of ductility were observed for the a-Si_0.32C_0.32N_0.36 film. The enhanced performance is preserved after the thermal exposure in air (up to 1100 °C) and vacuum (up to 900 °C) atmosphere. Annealing in oxidizing atmosphere has a beneficial effect in terms of tribological properties. Harder films with lower nitrogen content suffer from higher brittleness. FIB-SEM identified film-confined cracking as the initial failure event in SiC, while it was through-interface cracking for SiCN at higher loads. This points out on the higher fracture resistance of the SiCN films where higher strains are necessary for crack formation

The scratch test, as probably the most widespread technique for assessment of the adhesive/cohesive properties of a film–substrate system, fully depends on reliable evaluation based on assessment of critical loads for systems’ failures. Traditionally used evaluation methods (depth change record and visual observation) may sometimes give misleading conclusions about the failure dynamics, especially in the case of opaque films. Therefore, there is a need for another independent evaluation technique with the potential to complete the existing approaches. The nondestructive method of acoustic emission, which detects the elastic waves emitted during film cracking and delamination, can be regarded as a convenient candidate for such a role even at nano/micro scale. The strength of the combination of microscopic observation of the residual groove and depth change record with the acoustic emission detection system proved to be a robust and reliable approach in analyzing adhesion/cohesion properties of thin films. The dynamics of the gradual damage taking place during the nano/micro scratch test revealed by the combined approach is presented for SiC and SiCN thin films. Comparison of critical load values clearly reflects the higher ability of the AE approach in detecting the initial material failure compared to the visual observation.

Zinc and its alloys belong to a group of biodegradable materials, which can be potentially used for the preparation of temporary orthopedic implants. The research of biodegradable zinc materials revealed a lot of limitations; however, the new processing approaches of those materials can enhance their properties, which are insufficient for now. In this study, the zinc composite with 8 wt.% of hydroxyapatite (Zn/HA8) prepared for the first time by extrusion process was characterized from the point of view of the structural, mechanical and corrosion properties. The extrusion process led to good integrity of the interfaces between the zinc and hydroxyapatite particles. Mechanical behavior confirmed the role of hydroxyapatite as a defect in the material structure, which led to a decrease of the Zn/HA8 mechanical properties by approximately 30% (compressive yield strength (CYS) = 154 MPa Zn, 113 MPa Zn/HA8). Despite that, the Zn/HA8 composite showed sufficient mechanical properties for cancellous bone replacement and reached the lower limit for cortical bone. Additionally, the presence of hydroxyapatite caused the preferential precipitation of hydroxyapatite (HA) from the solution and can lead to a significant enhancement of the tissue/implant interface interactions.