In this paper, we present an innovative bilaterally-controllable self-locking mechanism that can be applied to the micro in-pipe robot. The background and state of the art of the inchworm micro in-pipe robot is briefly described in the very beginning of the paper, where the main factors that influence the traction ability are also discussed. Afterwards, the micro in-pipe robots’ propulsion principle based on a unidirectional self-locking mechanism is discussed. Then, several kinds of self-locking mechanisms are compared, and a new bilaterally-controllable self-locking mechanism is proposed. By implementing the self-locking mechanism, the robot's tractive force is no longer restricted by the friction force, and both two-way motion and position locking for the robot can be achieved. Finally, the traction experiment is conducted using a prototype robot with the new bilaterally-controllable self-locking mechanism. Test results show that this new self-locking mechanism can adapt itself to a diameter of >17~>20 mm and has a blocking force up to 25N, and the maximum tractive force of the in-pipe robot based on such a locking mechanism is 12N under the maximum velocity of 10mm/s.
23 February 2015 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
In order to improve the efficiency of multi-actuator mobile robots hydraulic system, this paper proposes a new kind of cylinder whose effective area is variable. The new cylinder has multi chambers which can be connected with each other or to a main system circuit by controlling switching valves. On the one hand, the new cylinder can make sure that the load pressure of all actuators is almost equal through varying effective area. On the other hand, the new cylinder can realize the flow recovery through that return chambers are connected with feeding chambers. Therefore, the new cylinder can reduce overall machine energy consumption by reducing throttling losses and allowing energy recovery. The performance of the new cylinder is analyzed through building the mathematical model. Based on the evaluated results, in order to further improve the performance of the load match of the cylinder and avoid the deflection of the main piston, the structure of the cylinder is optimized. Finally, an optimized cylinder is shown in this paper which has well performance of the load match.
13 December 2018 in IOP Conference Series: Materials Science and Engineering
Taking the crawler amphibious vehicle as the research object, the dynamic system is designed with an extended-range structure. Based on the design parameters and performance indicators, the vehicle dynamics is used to calculate the power demand and torque demand of the dynamic system that meets the design conditions, and then the power component selection and matching calculation. Based on the CRUISE vehicle simulation software, the vehicle model of the extended-range structure is established. Design a constant temperature control strategy and the cycle run simulation and performance indicators verification are set. The designed extended-range dynamic system meets the design indicators, and the vehicle has powerful performance and meets the driving mileage requirements. Lay the foundation for subsequent laboratory bench testing.
At present, mobile robotic manipulators have been greatly developed. However, these further promotions are limited by a low load capacity and short operation time. The above problems can be improved by using a hydraulic drive mode and increasing the system energy efficiency. In this paper, a novel energy-efficient wobble plate hydraulic joint is presented, which has the characteristics of having a small size, lightweight, large load capacity, and high energy efficiency. Based on the efficiency analysis in traditional robotic manipulators, this paper presents a novel hydraulic joint with a multi-chamber drive structure. Kinematics model and dynamics model are both established for the analysis of the mechanical characteristics, and the functional relationship between the input and output is depicted by numerical simulation. Based on the structural characteristics and control principle, the load matching controller is designed and specific control processes are formulated. Combined with a strategy of load matching, the servo control system is established and the energy-saving effect is verified by simulation. The result shows that the wobble plate hydraulic joint can change connections between a high-pressure circuit and different working chambers, which realizes the match between the output torque and load torque. With the load matching controller, the energy consumption of the wobble plate joint is greatly reduced, which contributes to a considerably improved energy efficiency. The research in this paper not only lays a theoretical foundation for the development of a wobble plate hydraulic joint, but also provides guidance for the improvement of the hydraulic system energy efficiency in mobile robotic manipulators.
1 January 2018 in Journal of Mechanical Engineering
To improve the driving torque of the robots joint, a wobble plate hydraulic joint is proposed, and the structure and working principle are described. Then mathematical models of kinematics and dynamics was established. On the basis of this, dynamic simulation and characteristic analysis are carried out. Results show that the motion curve of the joint is continuous and the impact is small. Moreover the output torque of the joint characterized by simple structure and easy processing is large and can be rotated continuously.