Dewang Li

Mr. Dewang Li


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 November 2024 in Materials
Verified
Journal Article
Open access
PDF file
HCHuating Chen
Huating Chen
一卓一凡 卓
一凡 卓
DLDewang Li
Dewang Li
YHYan Huang
Yan Huang
Fracture tests are a necessary means to obtain the fracture properties of concrete, which are crucial material parameters for the fracture analysis of concrete structures. This study aims to fill the gap of insufficient test results on the fracture toughness of widely used ordinary C40~C60 concrete. A three-point bending fracture test was conducted on 28 plain concrete and 6 reinforced concrete single-edge notched beam specimens with various depths of prefabricated notches. The results are reported, including the failure pattern, crack initiation load, peak load, and complete load versus crack mouth opening displacement curves. The cracking load showed significant variation due to differences in notch prefabrication and aggregate distribution, while the peak load decreased nonlinearly with an increase in the notch-to-height ratio. The reinforced concrete beams showed a significantly higher peak load than the plain concrete beams, attributed to the restraint of steel reinforcement, but the measured cracking load was comparable. A compliance versus notch-to-height ratio curve was derived for future applications, such as estimating crack length in crack growth rate tests. Finally, fracture toughness was determined based on the double-K fracture model and the boundary effect model. The average fracture toughness value for C50 concrete from this study was 2.0 MPa·m, slightly smaller than that of lower-strength concrete, indicating the strength and ductility dependency of concrete fracture toughness. The fracture toughness calculated from the two models is consistent, and both methods employ a closed-form solution and are practical to use. The derived fracture toughness was insensitive to the discrete parameters in the boundary effect model. The insights gained from this study significantly contribute to our understanding of the fracture toughness properties of ordinary structural concrete, highlighting its potential to shape future studies and applications in the field.

11 December 2025 in Materials
Verified
Journal Article
Open access
PDF file
HCHuating Chen
Huating Chen
家宋家鹏 宋
家鹏 宋
DLDewang Li
Dewang Li
To obtain fatigue crack propagation properties of ordinary concrete commonly employed in bridge construction, 48 replicate single-edge notched beam specimens were fabricated using C50 plain concrete. Twelve of these were subjected to monotonic loading to determine their static capacity; the remaining 36 were fatigue-loaded with various combinations of maximum stress level and stress ratio under three-point bending. Visual observation, strain gauges, and the compliance method were used to determine the evolution of crack length during fatigue loading. The fatigue crack growth rates were then evaluated for each specimen using linear regression. This study shows that the fracture surface under fatigue loading exhibits greater zigzagging than under monotonic loading, with multiple microcracks coalescing. The elastic compliance method captures the three-stage development of fatigue crack well, and the derived equivalent crack size is consistently smaller than surface measurements. Significant scatter exists in the test data; however, the crack growth rate and stress intensity factor range follow a straight line on logarithmic scales, indicating that the Paris Law applies to plain concrete. The slope and intercept of C50 concrete, based on 27 fatigue-failed specimens, follow a Normal distribution, with means of 16.46 and −24.81 (in N-mm units), and coefficients of variation of 0.38 and −0.38, respectively. The corresponding mean and coefficient of variation for slope and intercept by the Forman Equation are 14.80 and 0.42 and −21.18 and −0.44, respectively. The fatigue crack in C50 concrete of this study shows a faster growth rate (46.7% larger slope) than that in lower-strength concrete in the literature. With further research needs identified, this study contributes to a better understanding of the fatigue crack growth properties of ordinary structural concrete, providing valuable information for fatigue assessment and service-life extension of existing concrete bridges.