The air-suction precision seeder for small seeds is a planting machine, characterized by precision, high efficiency, and ease of operation, that uses air suction technology to sow small grain seeds at set intervals and depths into the soil. However, the forced vibration, enhanced by the increase in the operating speed, affects the seeding accuracy of the seeder and limits the seeding efficiency. To study the influence of vibration conditions on the seed suction performance of the air-suction precision seeder, we developed a computational fluid dynamics–discrete element coupling method to construct a bidirectional fluid–solid coupling numerical simulation model of the seed suction process under vibration conditions. Within the range of operating speeds from 0.6 km/h to 8 km/h, we quantitatively studied the population movement under different vibration frequencies, vibration amplitudes, negative pressure values, and seeding disc speeds and verified the simulation model and its analysis results through bench tests. The numerical results show that the interaction between the vibration frequency, vibration amplitude, and negative pressure value has the most significant impact on the single-seed rate. In addition, via variance analysis and response surface analysis, the optimal range of negative pressure values for achieving high single-seed rates under different vibration frequencies (4~10 Hz), vibration amplitudes (3~7.5 mm), and seeding disc speeds (4~50 rpm) was determined. The results indicate that, rather than the higher the negative pressure value, the higher the seed suction rate, the optimal negative pressure value for achieving a high seed suction rate varies with the specific vibration frequencies and amplitudes.
This paper presents a valve-controlled pipeline humidification system aimed at achieving precise and uniform humidity regulation in the multi-layer cultivation environments of plant factories. Since grafted seedlings require stable humidity conditions for effective healing, the system was designed to enable fine-grained adjustments across different cultivation layers. A quadratic regression orthogonal rotational combination design was employed to investigate how valve opening angles affect mean relative humidity (MRH), and a regression prediction model was developed accordingly. The model exhibited strong predictive performance, achieving an R2 of 0.9907 and an average relative error of only 0.67%. The optimal valve-opening angles were 60°, 50°, and 50°, respectively, which ensured that the MRH remained above 90% throughout operation. Experimental verification confirmed that the model accurately predicted humidity responses, while the proposed system improved uniformity by reducing the humidity variation from 6.1% to 0.3% and increasing the compliance rate from 58.3% to 100%. To enhance short-term humidity forecasting, three machine learning algorithms—Random Forest, XGBoost, and Transformer—were trained to predict humidity trends within a 6-h window. Among them, the RF model achieved the highest accuracy with an R2 of 0.9543, outperforming the other models in both stability and precision. The main contribution of this study is the identification of the optimal valve-opening combination through a quadratic orthogonal rotation regression combination experiment. Additionally, the RF obtained the optimal machine learning model for predicting humidity within 6 h.
For coarse-diameter electroplated diamond wires, the traditional horizontal sanding process suffers from inhomogeneous circumferential abrasive distribution, a lengthy manufacturing process, and poor production consistency. To address these issues, a pre-plating-free one-step electroplating process based on rotating magnetic field-assisted vertical sanding is proposed. Through the construction of a high-precision multi-process cooperative control system based on a dual-PLC architecture, systematic optimization of the process parameters from pre-treatment and electrodeposition to post-treatment is realized. Combined with the magnetohydrodynamic (MHD) and electrodeposition kinetic theories, the regulation mechanism of the rotating magnetic field-induced micro-convection effect on the mass transfer of the plating bath, particle dispersion, and grain refinement is revealed, and the kinetic principle by which the bottom-to-top vertical wire-running mode improves the circumferential deposition uniformity of abrasive grains on coarse-diameter wires is clarified. The experimental results show that the breaking force and the number of torsion cycles of the prepared diamond wire under the optimized process conditions are increased by 14.33% and 175.80%, respectively, and the properties of the head and tail ends of the wire exhibit high consistency. This study provides theoretical support for the industrial production of high-quality, high-consistency coarse-diameter diamond wires.
Diamond particles tend to disperse non-uniformly during the electroplating sand-setting process of diamond wire manufacture. To address this problem, the gas–liquid–solid three-phase flow characteristics in a baffled semi-circular reciprocating mixing tank were numerically analyzed by means of CFD(computational fluid dynamics). A VOF–DPM (Volume of Fluid–Discrete Phase Model) coupled gas–liquid–solid model was established to investigate the flow-field evolution within a stirring cycle, the velocity distribution characteristics, and the influence of the reciprocating frequency on mixing performance; the particle mixing uniformity of the reciprocating stirring device was further verified by sampling experiments. The results show that three typical dynamic vortex regions are formed in the tank, located above and below the stirring plate and outside the baffle, and the flow structure evolves periodically with the motion of the stirring plate. The reciprocating motion of the flat plate exerts a pronounced velocity-amplification effect on the fluid: the maximum axial velocity in the tank can reach 1.95 times the maximum velocity of the stirring plate. Increasing the reciprocating frequency raises the overall flow velocity and improves the uniformity of the velocity distribution, but does not change the basic flow pattern. Under the process condition of 0.5 Hz, which was evaluated experimentally by multi-point sampling (the CFD simulations were performed at 0.25, 0.62, and 1.00 Hz), the relative standard deviation of the diamond particle mass fraction is 4.62%, satisfying the requirements of the diamond wire electroplating sand-setting process. The results provide a theoretical basis for the structural optimization and process parameter regulation of reciprocating stirring devices for diamond wire sand-setting.