Ultrafine grained (UFG) and nanocrystalline metals (nc-metals) are studied. Experimental investigations of the behaviour of such materials under quasistatic as well as dynamic loading conditions related with microscopic observations show that in many cases the dominant mechanism of plastic strain is a multiscale development of shear deformation modes. The comprehensive discussion of these phenomena in UFG and nc-metals is given in M.A. Meyers, A. Mishra and D.J. Benson [Mechanical properties of nanocrystalline materials, Progr. Mater. Sci. 51 (2006), pp. 427–556], where it has been shown that the deformation mode of nanocrystalline materials changes as the grain size decreases into the ultrafine region. For smaller grain sizes (d < 300 nm) shear band development occurs immediately after the onset of plastic flow. Significant strain-rate dependence of the flow stress, particularly at high strain rates, was also emphasized. Our objective is to identify the parameters of Perzyna constitutive model, a new description of viscoplastic deformation, which accounts for the observed shear banding. The viscoplasticity model proposed earlier by Perzyna [Fundamental problems in viscoplasticity, Adv. Mech. 9 (1966), pp. 243–377] was extended in order to describe the shear banding contribution in Z. Nowak, P. Perzyna, R.B. Pȩcherski [Description of viscoplastic fow accounting for shear banding, Arch. Metall. Mater. 52 (2007), pp. 217–222]. The shear banding contribution function, which was introduced formerly by Pȩcherski [Modelling of large plastic deformation produced by micro-shear banding, Arch. Mech. 44 (1992), pp. 563–584] and applied in continuum plasticity accounting for shear banding in R.B. Pȩcherski [Macroscopic measure of the rate of deformation produced by micro-shear banding, Arch. Mech. 49 (1997), pp. 385–401] plays pivotal role in the viscoplasticity model. The derived constitutive equations were identified and verified with the application of experimental data provided in the article by D. Jia, K.T. Ramesh and E. Ma [Effects of nanocrystalline and ultrafne grain sizes on constitutive behavior and shear bands in iron, Acta Mat. 51 (2003), pp. 3495–3509], where quasistatic and dynamic compression tests with UFG and nanocrystalline iron specimens of a wide range of mean grain size were reported. Numerical simulation of the compression of the prismatic specimen was made by the ABAQUS FEM program with UMAT subroutine. Comparison with experimental results proved the validity of the identified parameters and the possibilities of the application of the proposed description for other high strength metals.

The subject of the study is the deformation of the oxygen-free high conductivity copper. The copper sample is given in the form of a foam. The sample undergoes an impact into an elastic wall. The strain rate hardening effect is investigated. The numerical model of the open-cell foam skeleton is prepared in the framework of the peridynamics method. The dynamic process of compression with different impact velocities is simulated. It has been found that the strain rate hardening effect is essential for the load-carrying capacity of the material under study. Taylor impact test of solid cylinder analysis precedes the analysis of the metallic foam.

The laser forming technique has an important disadvantage, which is the limitation of plastic deformation generated by a single laser beam pass. To increase the plastic deformation it is possible to apply external forces in the laser forming process. In this paper, we investigate the influence of external pre-loads on the laser bending of steel plate. The pre-loads investigated generate bending towards the laser beam. The thermal, elastic-plastic analysis is performed using the commercial nonlinear finite element analysis package ABAQUS. The focus of the paper is to identify how this pattern of the pre-load influence the final bend angle of the plate.

The mechanical properties and numerical model of ceramic alumina open-cell foam, which is produced by the chemical method of gelcasting with different cell sizes (porosities) are presented. Geometric characteristics of real foam samples were estimated from tomographic and scanning electron microscopy images. Using this information, numerical foam model was proposed. A good agreement between the numerical model and the results elaborated from microtomography was obtained. To simulate the deformation processes the finite element program ABAQUS was used. The main goal of this computation was to obtain macroscopic force as a function of applied vertical displacement in compression test.As a result of numerical simulation of compression test of alumina foam for different values of porosity, the Young modulus and the strength of such foams were estimated.

The subject of the study are alumina foams produced by gelcasting method. The results of micro-computed tomography of the foam samples are used to create the numerical model reconstructing the real structure of the foam skeleton as well as the simplified periodic open-cell structure models. The aim of the paper is to present a new idea of the energy-based assessment of failure strength under uniaxial compression of real alumina foams of various porosity with use of the periodic structure model of the same porosity. Considering two kinds of cellular structures: the periodic one, for instance of fcc type, and the random structure of real alumina foam it is possible to justify the hypothesis, computationally and experimentally, that the same elastic energy density cumulated in the both structures of the same porosity allows to determine the close values of fracture strength under compression. Application of finite element computations for the analysis of deformation and failure processes in real ceramic foams is time consuming. Therefore, the use of simplified periodic cell structure models for the assessment of elastic moduli and failure strength appears very attractive from the point of view of practical applications.