The performance of transistors based on two-dimensional (2D) materials is affected largely by the contact resistance due to high Schottky barriers at the metal-2D-material interface. In this work, we incorporate the effect of surrounding dielectrics and image-force barrier-lowering in calculating the resistance of Schottky edge-contacts between a metal and a transition-metal dichalcogenide (TMD) thin layer. The electrostatic potential is computed by solving the Poisson equation numerically. The transmission probability is computed using the Wentzel–Kramers–Brillouin (WKB) approximation using the full-band density of states obtained from density functional theory (DFT). The effect of the image force is obtained analytically using the Coulomb kernel of a point charge with boundary conditions appropriate to the geometry we have considered. We find that the image-force barrier-lowering (IFBL) in edge-contacts is determined mainly by the dielectric permittivity of the surrounding oxide. We find that low-κ surrounding dielectrics are crucial for obtaining low resistance monolayer-TMD edge-contacts. Our results show metal-to-n(p)-type MoS2 (WSe2) edge-contacts with SiO2 as top and bottom insulators, a doping concentration > 1 × 1013cm−2 and a metal work-function < 5.1 eV ( > 4.6 eV) result in a contact resistance as low as 50 Ω ⋅ μm.
A comprehensive quantitative root cause study of defect evolution leading to memory window closure from a charge balance and charge trapping perspective throughout all phases of a Si channel Hf0.5Zr0.5O2 (HZO) ferroelectric field-effect-transistor (FEFET) is reported. Starting with the first write pulse, an excessive SiO2 interlayer field is revealed that triggers the creation of defect levels Dit in excess of 1015 cm−2 eV−1 at the HZO–SiO2 interface screening ferroelectric (FE) polarization while enabling FE switching. Under subsequent early bipolar fatigue cycling (up to 104 cycles), defect creation commences at the SiO2–Si interface due to the high injected hole fluence (0.39 C/m2) during each stress pulse causing negative bias instability (NBI), which shifts the threshold voltage of the erase state VT,ERS by −0.3 V with accrual of permanently captured charge Nit of up to +5 × 10−3 C/m2 (3 × 1012 cm−2). Subsequently, Nit NBI generation at the SiO2–Si interface accelerates reaching levels of +7 × 10−2 C/m2, locking both FEFET program and erase drain current vs gate–source-voltage (ID–VGS) characteristics in the FEFET on-state inducing memory window closure at 105 cycles while FE switching (switched polarization Psw = 0.34 C/m2) remains essentially intact. These findings guide the down-selection toward suitable semiconductor/FE systems for charge balanced, reliable, and high endurance FEFETs.
In this theoretical study, we compare electrostatically doped metal-transition metal dichalcogenide (TMD) edge-contacts versus substitutionally doped edge-contacts in terms of their contact resistance. Our approach involves the utilization of electrostatic doping achieved by applying back-gate bias to the metal-TMD edge contacts, where carrier injection is primarily governed by the Schottky barrier at the interface. To analyze these contacts, we employ the Wentzel-Kramers-Brillouin (WKB) approximation to calculate the transmission coefficient and use density functional theory (DFT)-derived band structures. We numerically solve the Poisson equation to capture the electrostatic potential. We also account for the impact of the image force using Green's function for the Poisson equation with boundary conditions appropriate to our specific geometry. Our findings reveal that electrostatically doped TMD edge contacts exhibit higher contact resistance compared to impurity-doped edge contacts at equivalent carrier concentrations. At the same time, we find that, among the electrostatically doped edge contacts, a low- back-gate oxide in conjunction with low- top oxide is preferable in terms of improvement in contact resistance. For instance, in a metal-TMD edge contact scenario involving a monolayer as the channel, as the infinitely thick top oxide, and a back-gate oxide with an equivalent oxide thickness (EOT) of , we demonstrate that it is possible to achieve an impressively low contact resistance of when the back-gate bias exceeds or equals 2 V.
The performance of silicon nano-devices at cryogenic temperatures is critical for quantum qubit control circuits and space applications. Using multi-valley Monte Carlo simulations, we investigate electron transport in Si (110) systems. At low electric fields, phonon absorption becomes negligible, and mobility is governed by competition between remote Coulomb scattering at low inversion charge density and surface roughness scattering at high density, leading to a mobility peak. High- dielectrics such as introduce remote phonon scattering , which suppresses mobility. Under high electric fields, phonon emission dominates at 4 K, limiting velocity enhancement and resulting in limited current improvement.
We argue that the static dielectric constant of small (thin and/or narrow) semiconductor and insulator nanostructures depends strongly on their environment. We do so by considering the electronic response, simply reviewing, briefly but critically, the existing literature. Regarding the ionic response, in addition to reviewing the literature, we use a simple model to account for the confinement of optical phonons in thin films and show that the reduction of their density of states has a negligible effect on the dielectric constant, in contrast to some claims found in the literature. In general, we argue that in realistic structures, such as double-gated Si nanosheets, the use of the bulk dielectric constants for both the channel and the gate insulators is justified.