The paper presents complex analyses of geophysical site investigation results. The electrical resistivity method was used to investigate the potential pollutant migration pathways within areas of existing and former landfill sites. For the purpose of the present study, there were four municipal waste landfills and one industrial landfill chosen for further comprehensive analyses. The landfill bottom was isolated using geomembrane liner. However, ground water monitoring results revealed that the base was not leakage-free. Another two landfills were established in the past, when no containment systems were legally required. The geoelectrical investigation was the final part of an overall analytical assessment of the contaminated sites. The study was aimed at pollution spatial migration analyses and the interpretation of results, for further design of the reclamation and restoration plans. A clear correlation between pollution indicators such as salt compounds and electrical resistivity, allow aerial analyses and the precise determination of contaminated zones. The research results presented in the paper have been recently obtained and concern a period from 2010 to 2015.
Standard test methods may not be suitable or sufficient for determining the geotechnical conditions of a structure’s subsoil and the effects of the designed structures on the environment. Geophysical test methods, validated with other methods, may prove useful. In recent years they have found many new applications in engineering practice, both geotechnical and environmental. The advantages of geophysical methods include the non-destructive and non-invasive nature of the tests, their low costs and quick results, as well as compatibility with different materials, including soils, solid rocks, wastes and anthropogenic formations. The paper presents the analysis of laboratory and field investigations including research in a modified oedometer, resistivity chamber, electrical resistivity tomography (ERT) and resistivity cone penetration test (RCPT). Laboratory tests allowed for the assessment of the degree of saturation and porosity of sandy and clayey soils. The tests were carried out on saturated and unsaturated soil samples and allowed for the determination of some relationships between electrical conductivity and porosity. The proposed equations were used to assess parameters in in situ studies using RCPT tests and showed good agreement with reference values based on undisturbed soil samples. ERT tests confirmed the usefulness of electrical measurements in the quality assurance of subsoil and hydrotechnical structures. The tests showed weakening zones in the levee body, discontinuity of the vertical sealing system on the modernized section of the embankment, and location of the top of clay deposits.
1 January 2016 in Applied Ecology and Environmental Research
Soil parameters in agricultural areas play an important role in the migration of nitrogen compounds to groundwater. Nitrogen loss from subsoil depends on soil permeability, organic content, and soil saturation. Our study evaluates the parameters controlling the migration of nitrogen compounds through selected fine and sandy soils that may affect the quality of groundwater in agricultural areas. The results of this study indicate that denitrification processes that substantially affect ammonium (NH4+) and nitrate (NO3-) concentrations take place in fine soils. These processes decrease the flow of nitrogen into groundwater and are indicated by the production of a gashouse phase, a decrease in hydraulic conductivity, and a nitrogen compound concentration in the filtrate that is lower than the maximum concentration. Column tests have shown that the dominant transport process for silt loam and sand samples was advection, and the dominant transport process for loam was dispersion. Moreover, the velocities of NH4+ ion transport were lower than the velocities of water flow by approximately seven and five times for loam and sand, respectively. The estimated values of the retardation factor and dynamic sorption capacity for NO3- were lower than those for NH4+ ions. Finally, groundwater located below the silt loam and loam soil layers can effectively be protected against the infiltration of nitrogen compounds from agricultural sources.
Various types of trenchless methods are extensively used to create engineering barriers for the purpose of achieving relatively low hydraulic conductivity of the subsoil and hydrotechnical structures. The most commonly used technologies of the grouting curtain creating are the DSM (Deep Soil Mixing), WIPS (Vibro Injcted Thin Wall), low-pressure injection and jet-grouting. Vertical barriers are widely used in environmental control systems to restrict the lateral spreading of liquid or gaseous contaminants and for seepage control through and beneath a levees. The barrier walls are constructed in a single or two phases using a slurry composed mainly of bentonite, cementitious materials and water. Often to solve complex geotechnical problems the technologies are combined (e.g. combining DSM and jet grouting). In the paper some examples of practical application of chosen types of technology dedicated different problems solving are presented. The results of geotechnical investigations of hydraulic permeability, shear strength and depth control of cut-off wall are given. The tests were carried out using BAT system, Cone Penetration Tests (CPT) and drillings. The presented test results should help define the technical and financial criteria that should be used to compare grouting based methods and other techniques applicable to the same geotechnical special works. These recommendations should permit an adequate application of grouting techniques and contribute to finding solutions for the delicate problem of ground sealing, notably when proceeding with hydrotechnical or environmental structures placed below water table.
1 January 2008 in Annals of Warsaw University of Life Sciences – SGGW. Land Reclamation
The use of resistivity and seismic cone penetration tests for site characterization: The use of resistivity and seismic cone penetration tests for site characterization. Recent application of cone penetration tests to geotechnical and environmental site characterization has generated a wide collection of new sensors. This paper presents methods of interpreting geotechnical in situ investigations carried out by electrical resistivity (RCPT) and seismic (SCPT) cones. It contains some fundamental equations and the description of in situ electrical resistivity and shear wave velocity measurements and presents the results of SCPT and RCPT investigations at the experimental Stegny site in Warsaw. The aim of the paper is to present the approach to determination of shear wave velocity and porosity of clayey soils. According to the test results obtained, it can be concluded that both applied techniques are very useful to estimate the distribution of clay deposits and some of their geotechnical parameters.