Standard test methods may not be suitable or sufficient for determining the geotechnical conditions of a structure’s subsoil and the effects of the designed structures on the environment. Geophysical test methods, validated with other methods, may prove useful. In recent years they have found many new applications in engineering practice, both geotechnical and environmental. The advantages of geophysical methods include the non-destructive and non-invasive nature of the tests, their low costs and quick results, as well as compatibility with different materials, including soils, solid rocks, wastes and anthropogenic formations. The paper presents the analysis of laboratory and field investigations including research in a modified oedometer, resistivity chamber, electrical resistivity tomography (ERT) and resistivity cone penetration test (RCPT). Laboratory tests allowed for the assessment of the degree of saturation and porosity of sandy and clayey soils. The tests were carried out on saturated and unsaturated soil samples and allowed for the determination of some relationships between electrical conductivity and porosity. The proposed equations were used to assess parameters in in situ studies using RCPT tests and showed good agreement with reference values based on undisturbed soil samples. ERT tests confirmed the usefulness of electrical measurements in the quality assurance of subsoil and hydrotechnical structures. The tests showed weakening zones in the levee body, discontinuity of the vertical sealing system on the modernized section of the embankment, and location of the top of clay deposits.

Reducing the discharge of contaminants present in runoff water is important for a clean environment. This paper analyses field test results of three pilot-scale horizontal runoff water treatment zones filled with mixtures of zero valent iron (ZVI), activated carbon (AC), silica spongolite (SS), zeolite (Z), and limestone (LS). The investigated systems were (S1) ZVI/AC/SS, (S2) ZVI/AC/Z and (S3) ZVI/AC/LS. The efficiency of the three systems in the removal of Cd, Cu, Ni, Pb, Zn, COD and ammonium ions from runoff water was compared and the factors (temperature, pH, redox potential, hydraulic conductivity) and relationships affecting treatment effectiveness were determined. A statistical analysis of effluent contaminant concentrations and physicochemical parameters of effluent solutions included descriptive statistics, analysis of variance (ANOVA), a multidimensional analysis using a Principal Component Analysis (PCA), a factor analysis (FA) and a cluster analysis (CA). The ANOVA and cluster analyses indicated similarities between systems containing SS and LS. As a consequence, using cheaper SS can reduce investment costs. In addition, there were no significant differences between the three systems regarding Cd and Ni removal, while Cu and Pb were removed to almost 100%. The results indicate that all the tested materials supported ZVI and AC in the removal of heavy metals in a similar way. However, runoff water was enriched with nitrogen oxides and sulfates while flowing through treatment zones with SS and LS. The enrichment increased with increasing temperature and redox potential. The conducted analyses indicate that the most suitable mixture is ZVI/AC/Z. It should be emphasized that the ongoing processes (precipitation and ZVI corrosion) reduced the hydraulic conductivity of the filters up to two orders of magnitude. Expansive iron corrosion was the most limiting factor in ZVI filtration systems. In the future, applications decreasing the percentage of ZVI in the mixture are suggested.

Nowadays, in geotechnical engineering, laboratory investigations are necessary in order to assess their engineering properties, like stiffness characteristics. Knowledge about soil shear modulus (G) in a strain range of 1.0⋅10⁻⁴÷1% is very important to solve soil response subjected to dynamic loading. For purpose of that paper, shear modulus (G) of compacted sandy clay was measured in Water Centre – Laboratory, at Warsaw University of Life Sciences – SGGW by means of three different laboratory techniques, i.e., resonant column (RC), bender element (BE) and torsional shear (TS). Two methods of travel time identification in BE testing were applied: start to start (STS) and peak to peak (PTP). A brief description of these experimental techniques is given, with a special attention to strain level and excitation frequency they relate to. The main objective of this paper is to compare static against dynamic test results and monotonic against cyclic for cohesive compacted soil. In the next step, the behaviour of compacted sandy clay was compared with the behaviour of natural soil. The results suggest that in the case of BE measurements soil stiffness tends to be overestimated compared with stiffness obtained by RC and/or TS tests. The RC results are in good agreement with TS test results. The results received from the analyzed techniques indicate significant change in shear modulus with frequency and strain. The comparison of the results from different tests should be done at similar frequencies and referred to the same strain level. It is also shown that natural material is characterized by a greater stiffness than a compacted one.

There is a growing global trend toward reducing the consumption of natural resources and newly produced construction materials by replacing them with secondary raw materials. Concrete derived from construction and demolition waste can be recycled multiple times and is considered environmentally sustainable. This study evaluates the feasibility of reinforcing weak subsoil using crushed recycled concrete. Concrete obtained from the demolition of residential buildings was crushed under laboratory conditions to produce material with grain sizes corresponding to sands, and mixtures were subsequently prepared containing up to 30% fine fraction. The case study focuses on circular wind turbine foundations supported by symmetrically arranged columns made of four different materials, located beneath the foundation slab. The analyzed subsoil is characterized by strong stratification, low bearing capacity, and high compressibility. The calculation results indicate that the bearing capacity conditions for all foundations were met within similar ranges of the safety factor for the given loads, both for low- and high-power turbines. However, foundation deformations increased with turbine size and bending moments, and were nearly twice as large for recycled aggregates compared to recycled concrete. Numerical simulations demonstrate that recycled aggregate without fine fraction, as well as with fine fraction, and recycled concrete can provide load-bearing performance comparable to conventional concrete under low loading conditions, while offering significant environmental benefits.