Although equipment-based gas sensor systems (e.g., high-performance liquid chromatography) have been widely applied for formaldehyde gas detection, pre-treatment and expensive instrumentation are required. To overcome these disadvantages, we developed a colorimetric sensor based on polymer-based core–shell nanoparticles (PCSNPs), which are inexpensive, stable, and exhibit enhanced selectivity. Spherical and uniform poly(styrene-co-maleic anhydride) (PSMA)/polyethyleneimine (PEI) core–shell nanoparticles were prepared and then impregnated with Methyl Red (MR), Bromocresol Purple (BCP), or 4-nitrophenol (4-NP) to construct colorimetric sensors for formaldehyde gas. The intrinsic properties of these dyes were maintained when introduced into the PCSNPs. In the presence of formaldehyde, the MR, BCP, and 4-NP colorimetric sensors changed to yellow, red, and gray, respectively. The colorimetric response was maximized at a PEI/PSMA ratio of four, likely owing to the high content of amine groups. Effective formaldehyde gas detection was achieved at a relative humidity of 30% using the MR colorimetric sensor, which exhibited a large color change (92%) in 1 min. Advantageously, this stable sensor allowed sensitive and rapid naked-eye detection of low formaldehyde concentrations (0.5 ppm). Hence, this approach is promising for real-time formaldehyde gas visualization and can also be adapted to other colorimetric gas sensor systems to improve sensitivity and simplicity.

An ideal dye‐based sensing array has essential design requirements, including facile preparation methodology, tolerance to water vapor, a broad range of color‐responsive changes, and a simple readout system. Here, a brief synthetic route is developed for ion‐pairing dyes exhibiting unusual chromatic changes across the entire visible spectrum. It requires only mixing and precipitation under mild conditions. The dyes are applied to a sensing array containing 12 sensing elements with different initial states. Owing to the numerous color variations of the dyes, the color map generated by the array is highly simple yet sufficiently accurate to distinguish among the different functional groups (such as amines, aldehydes, and carboxylic acids) as well as carbon chain lengths. Principle component analysis (PCA) demonstrates that volatile organic compounds (VOCs) can be well classified according to the color changes of the sensing array. The ion‐pairing dyes are embedded into 3D stacked nanofibers via electrospinning, and function as effective harmful‐gas (e.g., formaldehyde) sensors with sub‐ppm theoretical detection limits (0.15 ppm). Finally, the 3D stacked nanofibers can be employed in an optoelectronic filter system that automatically checks for formaldehyde in the surroundings and also confirms the effective removal of the detected formaldehyde by the gas filter cartridge.

Polyglycolic acid (PGA) is a promising polymer in the packaging field owing to its excellent hydrolysis, heat resistance, and gas barrier properties, but it is limited in application due to its poor toughness. For this reason, a covalently bonded chain extender is introduced to increase compatibility with flexible polymers. However, covalent bonds are unfavorable for application to degradable plastics because of the energy required for reverse reactions. Therefore, we intended to effectively control the ductility of blending plastics by using a novel ionic chain extender with a relatively weaker non-covalent bond than the existing covalent bond. Polycaprolactone (PCL), which has biodegradability and flexibility, was selected as a blending polymer. For comparison, a covalently reactive chain extender (G-CE) and a non-covalently ionic chain extender (D-CE) were synthesized and compounded with blending plastics. Each chain extender improved the compatibility between PGA and PCL, and the ductility of the PGA/PCL blending plastics was more greatly enhanced with non-covalently bonded D-CE than with covalently bonded G-CE. At this time, the ductility of the PGA/PCL(90/10) blending plastic without CE was 7.2%, the ductility of blending plastic with D-CE (10D) was 26.6%, and the ductility of blending plastic with G-CE (10G) was 18.6%. Therefore, it was confirmed that the novel ionic chain extender inducing non-covalent bonds improves the compatibility between PGA and PCL and is more advantageous in enhancing ductility through a reversible reaction.

In this study, the coating order of two monomers in the shell polymerization process of core-shell nanoparticles was altered to facilitate easy coating and optimize the properties of the coated surface to simplify the additional coating formulation process. To obtain a glass transition temperature suitable for coating, a core was synthesized by the copolymerization of an acryl monomer. A perfluoro monomer and silane monomer were additionally added to synthesize nanoparticles exhibiting both water–oil repellency and anchoring properties. In order to realize various surface properties, the nanoparticles underwent surface modification and cellulose fiber was introduced. Through the various data described in this text, the surface properties improved with the order of the introduction of the two monomers.