Nanocomposites containingTiO₂ and activated carbon were obtained by the sol-gel method in the presence of Brij 58 surfactant. The sample with a higher surface area (185.6 m²/g) was promoted with Fe by impregnating it with aqueous solution of Fe(NO₃)₃. The obtained iron loadings, measured using X-ray fluorescence, were 0.83%, 3.30% and 7.17%. TiO₂ anatase was identified in all the samples by X-ray diffraction and Raman spectroscopy, but the presence of iron oxides could not be detected. However, infrared spectroscopy indicated the existence of Fe-O and Fe-O-Ti bonds. X-ray photoelectron spectroscopy revealed the presence of Fe²⁺ for samples with a lower Fe content and a mixture of Fe²⁺ and Fe³⁺ in the sample with 7.17% Fe. UV-Vis and photoluminescence spectroscopy showed the presence of carbon and Fe alongside TiO₂. This combination led to new properties due to the generation of intermediate energy levels and defects, contributing to an enhancement in the photocatalytic performance. The highest photodegradation efficiency of Congo red in solution (84.46%) was obtained for the sample with 7.17% Fe under visible light irradiation and acidic conditions. The synergistic contribution of dye adsorption and photodegradation was demonstrated, taking into account ZPC values of nanocomposites. Kinetic studies were completed with reaction mechanisms based on the results obtained in the presence of scavengers.

TiO₂ mesoporous supports were obtained by the sol–gel method from different precursors (titaniumethoxide, isopropoxide, or butoxide) in the presence of nonionic, cationic, and anionic surfactants. Among these samples, those obtained from Ti isopropoxide, Brij58 w/o activated carbon (AC), were selected as supports. Photocatalysts were obtained by modifying these supports with Ag, Fe, and AgFe (each metal around 1% mass). The characterization results showed a stronger influence of titania precursors, surfactants, and AC on the texture and an insignificant effect on the crystalline structure and morphology of the obtained materials. X-ray photoelectron spectroscopy revealed the effects of AC and Fe on the Ag⁰ concentration and of Ag on Fe-reduced species. Based on this information, the results obtained by H₂-TPR, UV–Vis, Raman, and photoluminescence spectroscopy were explained. The performance of the photocatalysts was evaluated in the degradation of Congo Red (CR) and Crystal Violet (CV) dyes under UV and visible light. The Ag-TiO₂ sample exhibited the best activity in degrading CR at acidic pH and in degrading CV under basic conditions. In visible light, we observed the significant effects of the surface plasmon resonance, AC, Ag, and Fe on the activity in CR photodegradation. The proposed kinetics and mechanisms complete the study of the reactions.

In this research, electrodeposition procedure was utilized for the synthesis of a new composite polymer: N-methylpyrrole–Triton–X100/N, N,N-diethylaniline (NMPY-TRX100/NNDEA) used as a coating on carbon steel type OL 37 electrode for corrosion protection. The surfactant Triton–X100, a dopant ion utilized throughout the process of electropolymerization, had a significant impact on the corrosion protection of this composite by impeding the penetration of corrosive ions. PNMPY-TRX100/PNNDEA coatings were successfully realized on the OL37 substrate by a galvanostatic method of synthesis using the solutions 0.1 M NNDEA, 0.1 M MPY, 0.03 M TRX-100, and 0.3 M H₂C₂O₄, at varied current densities (3 mA/cm², 5 mA/cm² and 8 mA/cm²) in different molar ratios (1:1, 1:5, 3:2 and 5:1). The deposition was performed for 20 and 30 min. The polymeric composite coatings were characterized electrochemically, spectroscopically, and morphologically by cyclic voltammetry, Fourier transform infrared spectroscopy, and scanning electron microscopy methods. Corrosion protection performance of PNMPY-TRX100/PNNDEA-coated OL 37 was examined through potentiostatic and potentiodynamic polarization, open circuit potential measurements, and electrochemical impedance spectroscopy procedures in 0.5 M H₂SO₄ media. The corrosion rate of PNPMPY-TRX100/PNNDEA-coated OL 37 was denoted to be around nine times less than that of an uncoated electrode. The corrosion protection yield of the coating was more than 90%. The best effectiveness was realized for PNMPY-TRX-100/PNNDEA by electrodeposition at 5 mA/cm² current density applied in molar ratios of 5:1 and 3:2, and at 8 mA/cm² current densities applied in molar ratio 5:1. The outcomes of the corrosion experiments revealed that PNMPY-TRX-100/PNNDEA coatings provide a good anticorrosion protection of OL 37 in corrosive solutions.

The fields of healthcare and pharmaceutical science are increasingly focused on developing innovative and effective treatments. This trend is driven by a growing consumer demand for natural, sustainable, and highly functional polymer-based products. This study focuses on two biomaterials: chitosan and royal jelly. Chitosan, a linear polysaccharide derived from chitin, is well-regarded for its hemostatic and antimicrobial properties, making it an excellent candidate for wound healing applications. Royal jelly, a nutrient-rich secretion from honeybees, represents a complex mixture of proteins, lipids, vitamins, and antioxidants, notably 10-hydroxy-2-decenoic acid (10-H2DA). It is known for its anti-inflammatory, antioxidant, and regenerative effects on the skin. While the individual benefits of chitosan and royal jelly are well-documented, there is a significant research gap concerning their synergistic application in various treatments such as topical formulations, wound healing, regenerative medicine, and delivery transport processes. Ultimately, this review concludes that the synergistic effects of chitosan and royal jelly could provide a material platform with a superior dual-action profile, integrating the structural and antimicrobial benefits of chitosan with the powerful regenerative and anti-inflammatory effects of royal jelly. This synergy strongly supports their utility in developing next-generation, high-performance natural bioproducts for wound healing, bone regeneration, agriculture, or aquaculture applications.