Jiahe Poy

Mr. Jiahe Poy


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 October 2025 in Lubricants
Verified
Journal Article
Open access
PDF file
NANur Aisya Affrina Mohamed Ariffin
Nur Aisya Affrina Mohamed Ariffin
JPJiahe Poy
Jiahe Poy
KWKing Jye Wong
King Jye Wong
Jo-Han NgJo-Han Ng
Jo-Han Ng
William ChongWilliam Chong
William Chong
Hydrogen-fuelled internal combustion engines (H2ICEs) generate water vapour that can condense in the sump and form water-in-oil emulsions, altering lubricant performance. This study measures the viscosity–temperature behaviour, copper corrosivity, and boundary tribology of three commercial oils—synthetic (5W-40), semi-synthetic (10W-40), and mineral (15W-40)—emulsified with 5–40 wt% water and tested in both freshly emulsified and aged (3 months; clarified oil layer) states. In fresh emulsions, viscosity rose with water fraction. At 25 ∘C and 40 wt%, the increase was 44.4% (5W-40), 78.7% (10W-40), and 81.2% (15W-40) versus the neat oils. Ageing drove viscosities toward the baseline, with the strongest effect observed for 15W-40, indicating destabilisation. The Vogel–Fulcher–Tammann (VFT) model was fitted to all datasets (RMSE < 5%). A VFT-based screening map uses two ratios at the friction test temperature: Rη=η/ηneat (relative film-forming tendency) and Rs=S/Sneat with S=B/(T−T0)2 (thermal-thinning sensitivity). A Preferred regime, Rη≥1.25 and Rs≤0.95, is correlated with lower friction, smaller wear scars, and copper rating 1a, with most aged conditions migrated out of this regime. Under boundary conditions, 5–10 wt% water generally reduced friction, whereas higher fractions and ageing increased friction and wear. Synthetic oil (5W-40) showed the most robust response.

25 May 2026 in Lubricants
Verified
Journal Article
Open access
PDF file
RNRaudah Nordin
Raudah Nordin
NANur Aisya Affrina Nur Aisya Affrina
Nur Aisya Affrina Nur Aisya Affrina
JPJiahe Poy
Jiahe Poy
Jo-Han NgJo-Han Ng
Jo-Han Ng
KWKing Jye Wong
King Jye Wong
William ChongWilliam Chong
William Chong
Lubricant additive optimisation, such as using an Organic Friction Modifier (OFM), often relies on empirical methods because the role of interfacial energetics in boundary lubrication remains uncertain. This study explores how interfacial energy interactions affect the tribological performance of glycerol monooleate (GMO)–polyalphaolefin-4 (PAO4) blends using ball-on-disk friction and wear tests. The 7 wt% GMO blend showed the best results, with friction reduced by about 4 times and the wear scar diameter by nearly 6 times compared to neat PAO4. Film-thickness estimates indicate that all tests operated within the boundary-to-mixed lubrication regime, suggesting that friction reduction is associated with interfacial interactions rather than hydrodynamic film formation. The Owens–Wendt–Kaelble surface energy analysis reveals that increasing GMO concentration shifts the lubricant’s dispersive–polar balance, with the 7 wt% formulation exhibiting dispersive–polar characteristics closer to those of the steel substrate. Low friction persisted as sliding velocity increased, and rupture-threshold analysis is consistent with improved tribological response under increasing load and sliding conditions. These findings suggest that the favourable tribological response observed for the investigated formulations may be associated with balanced interfacial energetic characteristics, particularly between dispersive and polar interactions. The observed friction and wear behaviour under increasing sliding conditions is interpreted in terms of friction and wear responses under boundary-dominated conditions, rather than through direct structural characterisation of boundary films. These trends are interpreted in relation to changes in dispersive and polar interactions at the interface. The results provide an interpretive framework for designing OFM systems that may be relevant to high-shear environments, including applications such as hydrogen internal combustion engines.