Within electrical contacts, poor electrical conductivity of lubricants can lead to triboelectric charging, causing electrostatic currents and thermal effects, which accelerate lubrication failure. This study aimed to address these challenges by producing and testing three greases with different base oils: ionic liquid ([Oley][Oleic]), synthetic oil (PAO4), and vegetable oil-based synthetic ester (trimethylolpropane oleate). Each grease was prepared with polytetrafluoroethylene powder as the thickener. The greases were tested using a custom-made tribometer, integrated with a grounded electrical current system, with friction tests conducted with up to a 2 A electrical current flow at a constant voltage supply of 4.5 V. Under triboelectric friction testing, [Oley][Oleic] grease outperformed a commercial perfluoropolyether grease by 27.7% in friction and 16.3% in wear. This grease also showed better performance than formulated lithium grease with extreme pressure additives. The study demonstrates that greases with low interfacial resistance can retain their lubrication capacity under triboelectric conditions. These results indicate that [Oley][Oleic] grease, with its ionic liquid base oil, offers a promising solution for applications involving electrical contacts. This study highlights the potential of using advanced base oils and thickeners to enhance the performance and sustainability of lubricants in demanding environments.
Hydrogen-fuelled internal combustion engines (H2ICEs) generate water vapour that can condense in the sump and form water-in-oil emulsions, altering lubricant performance. This study measures the viscosity–temperature behaviour, copper corrosivity, and boundary tribology of three commercial oils—synthetic (5W-40), semi-synthetic (10W-40), and mineral (15W-40)—emulsified with 5–40 wt% water and tested in both freshly emulsified and aged (3 months; clarified oil layer) states. In fresh emulsions, viscosity rose with water fraction. At 25 ∘C and 40 wt%, the increase was 44.4% (5W-40), 78.7% (10W-40), and 81.2% (15W-40) versus the neat oils. Ageing drove viscosities toward the baseline, with the strongest effect observed for 15W-40, indicating destabilisation. The Vogel–Fulcher–Tammann (VFT) model was fitted to all datasets (RMSE < 5%). A VFT-based screening map uses two ratios at the friction test temperature: (relative film-forming tendency) and with (thermal-thinning sensitivity). A Preferred regime, and , is correlated with lower friction, smaller wear scars, and copper rating 1a, with most aged conditions migrated out of this regime. Under boundary conditions, 5–10 wt% water generally reduced friction, whereas higher fractions and ageing increased friction and wear. Synthetic oil (5W-40) showed the most robust response.
Polyvinyl chloride (PVC) pyrolysis is constrained by chlorine release and undesirable product formation, limiting product quality and downstream utilisation. This study investigates the co-pyrolysis of PVC with eggshell (ES), a calcium carbonate-rich waste, to investigate its effects on chlorine chemistry, product distribution, and reaction kinetics. Thermogravimetric analysis confirms that the blends retain the characteristic two-stage degradation behaviour of PVC, while deviations in peak position and intensity indicate interactions between PVC and the calcium-rich phase. TGA–FTIR shows attenuation of C–Cl signals, indicating altered chlorine-containing species during co-pyrolysis. Py-GCMS shows increased mono-aromatic hydrocarbons from 58.1% in PVC to 71.9–78.6% in the blends, while bicyclic aromatics decrease from 11.1% to 5.1% and aldehydes from 13.3% to 1.5–2.3%. Synergism analysis indicates positive synergism for mono-aromatic formation and negative synergism for HCl, chlorinated hydrocarbons, and aldehydes relative to their theoretical contributions. The blends exhibit increased carbon content of 82.8–84.6 wt% and higher heating values of 36.5–37.1 MJ/kg. Kinetic analysis reveals conversion-dependent behaviour, with lower activation energies at early conversion followed by diffusion limitations at higher conversion. Overall, ES alters PVC pyrolysis through coupled chlorine and gas–solid interactions, favouring mono-aromatic formation while suppressing higher-aromatic and oxygenated pathway.