Conventional finite control set model-predictive control (FCS-MPC) presents a high computational burden, especially in three-level neutral-point-clamped (NPC) converters. This article proposes a low-complexity optimal switching time-modulated model-predictive control (OST-M2PC) method for a three-level NPC converter. In the proposed OST-M2PC method, the optimal switching time is calculated using a cost function. Compared with the conventional FCS-MPC, the proposed OST-M2PC method has a fixed switching frequency as well as better power quality. The proposed OST-M2PC can operate at a 20-kHz sampling frequency, reducing the computational burden of the processor. Simulation and experimental results validate the operation of the proposed method.

This paper describes a hybrid control scheme for a permanent magnet machine-based starter-generator (S/G) system. There has been increased usage of electric drive systems in the transportation sector for increased efficiency and reduced emissions. One of the advantages of utilizing suitable electric drives is the capability to operate as a starter or generator. The control design of such a system should be considered due to the operating requirements and fast load changes. Different control approaches should therefore be considered in order to achieve these goals, which are a current trend in the transportation sector. Model predictive control (MPC) is considered due to its very fast dynamic performance. In particular, modulated MPC (M ² PC) was recently introduced and showed significantly better performance than the standard MPC. The control scheme used in this paper utilizes M ² PC for the current inner loop and PI controllers for the outer loop. The use of M ² PC allows very fast transient-current response for the S/G system. The proposed overall control benefits from reduced current ripple when compared with a full cascaded PI control scheme. Simulation analyzes and experimental results show the capability and performance of the designed controller across both starter and generator modes.

Multilevel converters have been used for aircraft electric starter/generator (ESG) systems due to their high power qualities. One of the desirable topologies is the three-level neutral-point-clamped converter. Our studied ESG system operates at a high speed during its generation mode, which results in high modulation index and puts some specific challenges on neutral-point voltage balance, especially under low power factor load conditions. Moreover, common-mode voltage (CMV) needs to be addressed properly as it leads to irreversible damage of motor shaft bearings, thereby degrading the efficiency and reliability of the entire system. Compared with the conventional nearest-three virtual space vector technique, the proposed modulation scheme employs three adjacent medium vectors to synthesize a new medium vector and two pairs of large vectors to compose new small vectors. This allows the presented modulation scheme to achieve balanced capacitor voltage and reduced CMV at the same time. In addition, the torque ripple of the proposed modulation strategy is thoroughly compared and analyzed. Meanwhile, in order to overcome the heavy computational burden, a fast calculation approach is adopted to simplify the algorithm. Simulation results obtained from Simulink/PLECS and experimental results obtained from a 45 kW, 32 kr/min aircraft ESG system verify the effectiveness of the proposed strategy in more-electric-aircraft applications.

In this article, a virtual space vector based overmodulation algorithm is presented for three-level neutral-point (NP) clamped converters in high-speed aerospace motor drives. With the proposed inscribed polygonal-boundary compression technique, the output voltage capability is enhanced under a lower crossover angle and compression coefficient. As a result, it brings an opportunity for the operation of the studied aircraft electric starter/generator (ESG) systems easily extending from the linear modulation range into the overmodulation region. Furthermore, an active capacitor voltage balancing control method is investigated to recover NP potential imbalance in the case of high modulation index and low power factor operating conditions. To simplify the digital implementation of the algorithm, a fast calculation approach is adopted in this work. The modulation performance of the proposed strategy is verified by both simulation and experimental results with a 45 kW, 32 k r/min ESG prototype system.

Most loads of electrical power systems on a more electric aircraft (MEA) are regulated power converters. These loads behave as constant power loads (CPLs) that can significantly affect system stability. The system will become unstable and will be unable to operate at the rated power. In this article, a novel adaptive stabilization of a permanent magnet synchronous generator-based dc electrical power system in MEA is presented using a nonlinear feedback approach via loop-cancellation technique with a simple equation of feedback gain, which can be calculated from the power level of the CPL. The equation can be derived from a polynomial curve fitting based on the proposed mathematical model derived using the dq method. The adaptive stabilization results are validated by a small-signal stability analysis using the linearization technique, a large-signal stability analysis using the phase plane analysis, an intensive time-domain simulation using MATLAB, and experimentation. The results indicate that the proposed adaptive stabilization technique can provide the considered aircraft power system always stable for all operating conditions within the rated power, and the dc bus voltage can adhere to the MIL-STD-704F standard.

Synchronous reference frame proportional-integral (PI) current controller (CC) is considered the most well-established solution for the current regulation in electrical drives. However, the gain selection of the PI CC is still regarded to be poorly reported, particularly in relation to the effect of the inevitable execution time taken by the controller and inverter. Mostly, tuning process of PI CC is done by trial and error or using simple rules based on pole zero cancelation and pole placement methods which ignore time delays through the controller and inverter. Hence, PI CC delivers significantly different performance compared to the expected one during the digital implementation, especially if high bandwidth or low ratio between the switching and operational frequency are required. Therefore, this paper firstly addresses and analyses the common tuning rules of PI CC which ignore the existence of time delays followed by a rigorous analysis for PI CCs' robustness to the influence of computational and modulation delays. Based on this analysis, generic recommendations have been proposed to select the PI CCs' gains as a function of the electrical drive switching frequency considering the delay effect. A set of simple, generic, and fast tuning rules were derived that guarantee fast dynamic performance with reasonable stability margins. Moreover, the effects of model uncertainties on these developed rules have been analyzed and reported. Comprehensive experimental results are provided to prove the key analytical results of this study and to validate the proposed design recommendations.