Biomimetic microstructured surfaces offer a promising passive strategy for drag reduction in marine and aerospace applications. This study employs computational fluid dynamics (CFD) simulations to systematically investigate the drag reduction performance and mechanisms of groove-type microstructures, addressing both geometry selection and dimensional optimization. Three representative geometries (V-groove, blade-groove, and arc-groove) were compared under identical flow conditions (inflow velocity 5 m/s, Re = 7.5 × 105) using the shear-stress-transport (SST k-ω) turbulence model, and the third-generation Ω criterion was employed for threshold-independent vortex identification. The results establish a clear performance hierarchy: blade-groove achieves the highest drag reduction rate of 18.2%, followed by the V-groove (16.5%) and arc-groove (14.7%). The analysis reveals that stable near-wall microvortices form dynamic vortex isolation layers that separate the high-speed flow from the groove valleys, with blade grooves generating the strongest and most fully developed vortex structures. A parametric study of blade-groove aspect ratios (h+/s+ = 0.35–1.0) further demonstrates that maintaining h+/s+ ≥ 0.75 preserves effective vortex-isolation layers, whereas reducing h+/s+ below 0.6 causes vortex collapse and performance degradation. These findings establish a comprehensive design framework combining geometry selection (blade-groove > V-groove > arc-groove) with dimensional optimization criteria, providing quantitative guidance for practical biomimetic drag-reducing surfaces.
This study examines the microstructure and properties of 7A36 aluminum alloys processed through low-frequency electromagnetic casting (LFEC) with microalloyed Sc. Following secondary hot deformation, the addition of Sc refined the average grain size from 3.8 μm to 0.9 μm and reduced the deformed texture content. In the T6-aged condition, the combined application of Sc and LFEC enhanced the hardness (234 HV to 238 HV), ultimate tensile strength (647 MPa to 693 MPa), and elongation (EL). Fractographic analysis revealed brittle fracture modes dominated by cleavage, with minor intergranular contributions. The corrosion resistance was poorest in the rolled state and superior in the two-stage-aged state. Under two-stage aging, the maximum corrosion depth for the Sc-modified, LFEC-processed alloy decreased from 113.6 to 49.1 μm. The synergistic integration of Sc alloying and LFEC significantly improved both the mechanical properties and corrosion resistance.
8 April 2025 in Colloids and Surfaces A: Physicochemical and Engineering Aspects
V-shaped riblets are widely studied shark-skin-inspired microstructures, but their continuous high-fidelity replication on soft hyperelastic substrates remains challenging because large substrate deformation complicates complete profile filling. This study establishes an Abaqus-based finite-element process-window and morphology-screening method for roll-to-roll (R2R) hot embossing of 100 m-scale V-shaped riblets on a fluoroelastomer (FKM) sheet as a model hyperelastic substrate. A Yeoh hyperelastic law calibrated from room-temperature uniaxial tension was implemented in a three-dimensional large-deformation contact simulation. Embossing temperature T and imposed nip-compression depth D were examined as screening variables, with formed riblet height, filling ratio, and auxiliary field indicators used to evaluate the forming response. The simulated filling ratio increased from about 69% to 76% as T increased from 120 to 180 °C and from about 39% to 76% as D increased from 60 to 120 m, indicating that nip-compression depth exerted the stronger geometric control over profile filling. R2R hot embossing experiments and laser-confocal profilometry evaluated the retained riblet morphology. For the 160 °C D-series, the measured retained morphology followed the simulated filling trend, with a filling-ratio RMSE of 3.09 percentage points and top-width RMSE of 2.01 m. The integrated numerical–experimental framework provides an experimentally supported manufacturing basis for process-window selection and retained-morphology control in the R2R hot embossing of riblet-textured hyperelastic sheets.