Qualitative and quantitative changes in anatomical characteristics of charcoal from Campomanesia xanthocarpa, Eugenia pyriformis, Myrcia retorta and Plinia peruviana were described to provide its correct discrimination and information’s to contribute to evaluations in illegal logging. The material came from Planalto Catarinense region, southern Brazil. For each species, three discs at diameter at breast height were collected from three randomly selected trees. All the disks were sectioned to obtain samples in different positions of the trunk (bark, intermediate and pith). Samples were wrapped in aluminum foil and carbonized in a muffle furnace, with a final temperature of 450 °C and a heating rate of 1.66 °C.min-1. In species analyzed, growth rings are few distinct, delimitated by fiber regions; solitary vessel and axial parenchyma diffuse or diffuse-in-aggregate is predominant. The wood to charcoal conversion caused variation in the following characteristics: vessel diameters decreased varying from 21.1% in Myrcia retorta to 33.4% in Eugenia pyriformis, while the vessel frequency increased with values from 50.7% to 92.3% related to the same species; height and width of the rays showed reduction, however, Myrcia retorta presented ruptures in ray cells and dimensions increased; ray frequency increased from 3.9% in Eugenia pyriformis to 54.1% in Campomanesia xantocharpa. Qualitative characteristics of wood from studied species remained in charcoal after carbonization at 450 ºC, being possible to discriminate the material based on wood anatomy. In charcoal, vessels dimensions and frequency, after ray characteristics can be applied as first step in this Myrtaceae species distinction at forest control.
16 November 2019 in Wood Material Science & Engineering
Because of the species similarity and the need to differentiate wood of the Myrtaceae family, this study aimed to evaluate the potential of near-infrared spectroscopy for discrimination of wood and charcoal from Campomanesia xanthocarpa Berg, Eugenia pyriformis Cambess., Myrcia retorta Cambess. and Plinia peruviana (Poir.) Govaerts, native of the Araucaria Forest. For each evaluated species, three trees were collected and a disk at breast height was cut and divided into samples obtained in the region near the pith, intermediate and near the bark. For each sample, two spectra were obtained in each anatomical section (transversal, radial and tangential) in the region from 4000 to 10,000 cm−1. Results indicated the similarity of wood and charcoal spectra of all species, and principal component analysis (PCA) of raw data on samples showed little distinction of species, but second derivative pretreatment provided adequate discrimination. When evaluation was based on anatomical sections and position in trunk, for wood in all positions (near bark, intermediate, near pith) it was possible to separate species, but for charcoal some more samples dispersion were observed. Linear discriminant analysis corroborated the results of PCA. Near-infrared spectroscopy presented adequate results and the potential to help discriminate wood and charcoal of the four Myrtaceae species.
A densidade básica da madeira é considerada uma das propriedades mais importantes, pois influencia diretamente as demais características físicas para a utilização industrial. O presente estudo teve como objetivo determinar a densidade básica média da madeira de árvores de Pinus patula Schltdl & Cham. e analisar a sua variação nos sentidos radial e longitudinal. As amostras foram retiradas de 12 árvores com 9 anos de idade, ao longo dos eixos longitudinal e radial. A densidade básica média observada foi 0,307 g cm-³. Observou-se aumento da densidade básica no sentido medula-casca e decréscimo no sentido longitudinal apenas da base até 2 m. Foi verificada interação entre as variações nos sentidos radial e longitudinal da madeira, indicando que a densidade da madeira de P. patula varia nos diferentes sentidos de crescimento..
This paper aimed to evaluate the technological properties of particleboards produced with particles of unconventional species, bamboo of the species Phyllostachys edulis, and of the genus traditionally used by the sector for the production of the particulate panels in Brazil, Pinus spp.The bamboo splints of 3 years old were collected in Frei Rogério, Santa Catarina, being transformed into particles in a mill hammer, while the particles of Pinus spp. were collected from the industrial process of MDP production in Bonet Madeiras e Papéis Ltda Company in Santa Cecília, Santa Catarina. The company used eight-year-old logs of P. taeda and P. elliottii from the thinning process, without distinction of the species. The experiment was composed of five compositions with mixing the bamboo and wood particles in different proportions ((T1)100:0%; (T2)75:25%; (T3)50:50%; (T4)25:75%; (T5)0:100%). The panels were produced nominal density of 700 kg / m³ and pressing cycle of 160ºC and 40 kgf/cm² for 8 minutes. Results reporting physical and mechanical properties of panels were evaluated through Analysis of Variance and Tukey´s Test at 95% probability. The results evidenced that bamboo particles presented potential for the production of particleboard. The most promising results were presented with the addition of 50% of bamboo in the panel composition (T3), mainly by means observed for dimensional stability, as for strength and stiffness. Values of internal bond presented significantly lower averages with the addition of more than 25% of bamboo.