This study synthesizes two highly water-soluble copolymers, p(SA-co-SMAS) and p(SA-co-SMAS-co-AMPS) using sodium alginate (SA), sodium 2-methylprop-2-ene-1-sulfonate (SMAS), and 2-acrylamido-2-methylpropane sulfonic acid (AMPS, with or without addition) as precursors. Under ball milling, these copolymers are blended with aluminum sulfate and glass fibers to produce two series of cement admixtures. Compared to systems without admixtures or with pure aluminum sulfate as sole admixture, the admixture obtained from p(SA-co-SMAS) and aluminum sulfate significantly shortens the initial setting time (4.47 vs. 33.59 and 29.51 min) and final setting time (8.46 vs. 45.26 and 35.12 min), while markedly improving compressive strength (9.2 vs. 3.5 and 4.3 MPa) and flexural strength (3.5 vs. 1.0 and 1.1 MPa). This enhancement is attributed to the formation of a unique boehmite (AlO(OH)) phase in synthesized admixture, which rapidly reacts with tricalcium silicate, gypsum, and water in cement to form ettringite (Ca6Al2(SO4)3(OH)12·26H2O). The ettringite interlocks with the two-dimensional C–S–H gel, creating a stable three-dimensional network. Further blending this admixture with 200-mesh glass fibers yields a new admixture containing Al4SO4(OH)10·36H2O. Compared to boehmite, this phase further reduces setting times and increases average compressive strength (10.2 vs. 9.2 MPa). The admixture derived from p(SA-co-SMAS-co-AMPS) and aluminum sulfate shows even better performance: setting times are further shortened and flexural strength is significantly enhanced, owing to the presence of the more effective Al4SO4(OH)10·36H2O phase. Incorporating 200-mesh glass fibers into this system results in the shortest setting times (initial: 2.24 min, final: 5.73 min) and an excellent 24 h compressive strength (9.4 MPa), likely due to a unique and unexpected pore-filling effect. In contrast to conventional uses of sodium alginate as a retarder, glass fibers as mere reinforcements, and aluminum sulfate as a strength-impairing accelerator, this work demonstrates a synergistic strategy, which enables an ultra-rapid and high-strength cement setting process, offering highly significant scientific and practical value.
This study presents a new ternary copolymer synthesized via aqueous free-radical polymerization from sodium humate, sodium 2-methylprop-2-ene-1-sulfonate (SMAS), and 2-acrylamido-2-methylpropane sulfonic acid (AMPS). The resulting highly water-soluble, three-dimensional porous copolymer is complexed with aluminum sulfate to form a composite admixture containing AlO(OH), which acts as a highly effective accelerator for cement hydration. This system significantly shortens the initial and final setting times to averages of 2.62 min and 4.53 min, respectively, and enhances early-age mechanical strength (1.7 MPa compressive, 1.4 MPa flexural at 6 h). These improvements are correlated with the formation of key crystalline phases, including Al2Si2O5(OH)4 and Ca3Al2O6·xH2O gel. Incorporation of 50-mesh carbon fibers further reduces setting times (2.21 min initial, 3.93 min final) and increases 24 h strength (5.2 MPa compressive, 2.7 MPa flexural), despite a slight reduction in early strength (at 6 h). In contrast, 200-mesh carbon fibers extend the initial setting time and diminish early strength, associated with the formation of less effective gel phases such as Ca3Al2O6·xH2O, (CaO)x(Al2O3)11, and Ca4Al2O7·xH2O. Among these, the Al2Si2O5(OH)4 phase demonstrates superior performance, while finer carbon fibers show limited effectiveness in bridging hydration products. Conventionally employed as retarders or reinforcing agents, humate-based polymers and carbon fibers are shown here to function as dual-functional admixtures—serving as efficient setting accelerators while enhancing mechanical properties through tailored material design. This strategy offers a promising pathway for developing advanced multifunctional cement admixtures.