Sidra Chaudhary

Dr. Sidra Chaudhary

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 October 2023 in Molecules
Verified
Journal Article
Open access
PDF file
QPQin Pan
Qin Pan
YWYong Wu
Yong Wu
AZAqun Zheng
Aqun Zheng
XWXiangdong Wang
Xiangdong Wang
XLXiaoyong Li
Xiaoyong Li
杨孙杨 孙
杨 孙
The C-3 modification of 1H-indazole has produced active pharmaceuticals for the treatment of cancer and HIV. But, so far, this transformation has seemed less available, due to the lack of efficient C-C bond formation at the less reactive C-3 position. In this work, a series of silica gel-supported PdO2 nanoparticles of 25–66 nm size were prepared by ball milling silica gel with divalent palladium precursors, and then employed as catalysts for the Suzuki–Miyaura cross-coupling of 1H-indazole derivative with phenylboronic acid. All the synthesized catalysts showed much higher cross-coupling yields than their palladium precursors, and could also be reused three times without losing high activity and selectivity in a toluene/water/ethanol mixed solvent. Although the palladium precursors showed an order of activity of PdCl2(dppf, 1,1′-bis(diphenylphosphino)ferrocene) > PdCl2(dtbpf, 1,1′-bis(di-tert-butylphosphino)ferrocene) > Pd(OAc, acetate)2, the synthesized catalysts showed an order of C1 (from Pd(OAc)2) > C3 (from PdCl2(dtbpf)) > C2 (from PdCl2(dppf)), which conformed to the orders of BET (Brunauer–Emmett–Teller) surface areas and acidities of these catalysts. Notably, the most inexpensive Pd(OAc)2 can be used as a palladium precursor for the synthesis of the best catalyst through simple ball milling. This work provides a highly active and inexpensive series of catalysts for C-3 modification of 1H-indazole, which are significant for the large-scale production of 1H-indazole-based pharmaceuticals.

25 September 2024 in Molecules
Verified
Journal Article
Open access
PDF file
ZSZhiyuan Song
Zhiyuan Song
SCSidra Chaudhary
Sidra Chaudhary
ZBZainab Bibi
Zainab Bibi
YWYong Wu
Yong Wu
QJQin-Xiang JIA
Qin-Xiang JIA
杨孙杨 孙
杨 孙
Two water-soluble block copolymers composed of acrylic acid (AA), 2-acrylamido-2-methylpropane sulfonic acid (AMPS), and optionally maleic anhydride (MAH) were synthesized through ammonium persulfate-catalyzed free radical polymerization in water. The introduction of aluminum sulfate (AS) into the resulting mixtures significantly reduced the setting times of the paste and enhanced the mechanical strength of the mortar compared to both the additive-free control and experiments facilitated solely by pure AS. This improvement was primarily attributed to the inhibition of rapid Al3+ hydrolysis, which was achieved through coordination of the synthesized block copolymers, along with the formation of newly identified hydrolytic intermediates. Notably, the ternary copolymer (AA–AMPS–MAH) exhibited superior performance compared to that of the binary copolymer (AA–AMPS). In the early stages of cement setting, clusters of ettringite (AFt) were found to be immobilized over newly detected linkage phases, including unusual calcium silicate hydrate and epistilbite. In contrast to the well-documented role of polymers in retarding cement hydration, this study presents a novel approach by providing both accelerating and hardening agents for cement setting, which has significant implications for the future design of cement additives.

12 February 2026 in Nanomaterials
Verified
Journal Article
Open access
PDF file
ZSZhiyuang Song
Zhiyuang Song
SCSidra Chaudhary
Sidra Chaudhary
DYDing Yan
Ding Yan
YJYan yu Jiao
Yan yu Jiao
YWYong Wu
Yong Wu
杨孙杨 孙
杨 孙
This study synthesizes two highly water-soluble copolymers, p(SA-co-SMAS) and p(SA-co-SMAS-co-AMPS) using sodium alginate (SA), sodium 2-methylprop-2-ene-1-sulfonate (SMAS), and 2-acrylamido-2-methylpropane sulfonic acid (AMPS, with or without addition) as precursors. Under ball milling, these copolymers are blended with aluminum sulfate and glass fibers to produce two series of cement admixtures. Compared to systems without admixtures or with pure aluminum sulfate as sole admixture, the admixture obtained from p(SA-co-SMAS) and aluminum sulfate significantly shortens the initial setting time (4.47 vs. 33.59 and 29.51 min) and final setting time (8.46 vs. 45.26 and 35.12 min), while markedly improving compressive strength (9.2 vs. 3.5 and 4.3 MPa) and flexural strength (3.5 vs. 1.0 and 1.1 MPa). This enhancement is attributed to the formation of a unique boehmite (AlO(OH)) phase in synthesized admixture, which rapidly reacts with tricalcium silicate, gypsum, and water in cement to form ettringite (Ca6Al2(SO4)3(OH)12·26H2O). The ettringite interlocks with the two-dimensional C–S–H gel, creating a stable three-dimensional network. Further blending this admixture with 200-mesh glass fibers yields a new admixture containing Al4SO4(OH)10·36H2O. Compared to boehmite, this phase further reduces setting times and increases average compressive strength (10.2 vs. 9.2 MPa). The admixture derived from p(SA-co-SMAS-co-AMPS) and aluminum sulfate shows even better performance: setting times are further shortened and flexural strength is significantly enhanced, owing to the presence of the more effective Al4SO4(OH)10·36H2O phase. Incorporating 200-mesh glass fibers into this system results in the shortest setting times (initial: 2.24 min, final: 5.73 min) and an excellent 24 h compressive strength (9.4 MPa), likely due to a unique and unexpected pore-filling effect. In contrast to conventional uses of sodium alginate as a retarder, glass fibers as mere reinforcements, and aluminum sulfate as a strength-impairing accelerator, this work demonstrates a synergistic strategy, which enables an ultra-rapid and high-strength cement setting process, offering highly significant scientific and practical value.

19 February 2026 in Journal of Molecular Structure
Verified
Journal Article
Closed access
MAMuhammad Faisal Altaf
Muhammad Faisal Altaf
BPBo Peng
Bo Peng
ZMZhuang Miao
Zhuang Miao
OOOusseini Seidina Ousseini
Ousseini Seidina Ousseini
JHJixiang He
Jixiang He
SCSidra Chaudhary
Sidra Chaudhary

13 February 2025 in Nanomaterials
Verified
Journal Article
Open access
PDF file
ZSZhiyuan Song
Zhiyuan Song
SCSidra Chaudhary
Sidra Chaudhary
ZBZainab Bibi
Zainab Bibi
YWYong Wu
Yong Wu
QJQin-Xiang JIA
Qin-Xiang JIA
杨孙杨 孙
杨 孙
Two hydrophilic copolymers containing functional groups such as carboxyl, amido, and sulfonic acid are synthesized using ammonium persulfate-catalyzed free radical polymerization in water. Aluminum sulfate is then introduced, resulting in two polymer complexes that exhibit reduced cement setting times (initial, 1.16–2.44 min; final, 2.02–3.14 min) and improved compressive (24 h, 5.81–7.25 MPa) and flexural (24 h, 2.80–2.99 MPa) strengths compared to pure aluminum sulfate-facilitated cementing (initial, 19.11 min; final, 37.05 min; compressive, 24 h, 5.51 MPa; flexural, 24 h, 2.56 MPa). Following this, ball-milled illite powder is added, and the resulting admixtures further display slightly prolonged setting times (initial, 2.35–2.99 vs. 1.16–2.44 min; final, 3.98–4.35 vs. 2.02–3.14 min), along with comparable compressive strengths (5.85–7.11 vs. 5.81–7.25 MPa) and enhanced flexural strengths (3.92–5.83 vs. 2.80–2.99 MPa). Notably, a unique adhesive pozzolanic clinker, Ca54MgAl2Si16O90 (54CaO·MgO·Al2O3·16SiO2), emerges in the presence of illite-based admixtures, contributing to the mechanical strength development of the hydrated mortars. Although illite itself is hydrophobic, the coating of ball-milled illite powder with aluminum sulfate and copolymers facilitates its dispersion into the gaps and pores of the cement matrix during setting, thereby increasing the flexural strength. This work presents an interesting approach to utilizing illite materials in cement applications, which is significant for reducing CO2 emissions during cement production and use.

19 November 2024 in Molecules
Verified
Journal Article
Open access
PDF file
SCSidra Chaudhary
Sidra Chaudhary
QPQin Pan
Qin Pan
YWYong Wu
Yong Wu
ZBZainab Bibi
Zainab Bibi
XLXiaoyong Li
Xiaoyong Li
杨孙杨 孙
杨 孙
A series of Fe–Ba mixed oxides, including a pure Fe-containing sample as a reference, have been synthesized via a sol–gel process using Fe3+ or Fe2+ salts and BaSO4 as raw materials, with Pluronic P123 serving as a template. These oxides have been thoroughly characterized and subsequently utilized as catalysts for the chlorination of various organic molecules. Commercial hydrochloric acid, known for its relative safety, and environmentally friendly aqueous hydrogen peroxide were employed as the chlorine source and oxidant, respectively. The pure Fe-containing catalyst displays excellent thermal stability between 600 and 800 °C and exhibited moderate to high conversions in the chlorination of toluene, benzene, and tert-butyl hydroperoxide, with remarkable ortho-selectivity in chlorination of toluene. The combination of Fe3+ salt with BaSO4 in the sol–gel process results in a Fe–Ba mixed oxide catalyst composed of BaO2, BaFe4O7, and Fe2O3, significantly enhancing the chlorination activity compared to that displayed by the pure Fe catalyst. Notably, the chlorination of tert-butyl hydroperoxide (TBHP) does not require additional oxidants such as H2O2, and involves both electrophilic substitution and nucleophilic addition. Notably, the chlorination of bromobenzene yields chlorobenzene as the sole product, a transformation that has not been previously reported. Overall, this catalytic chlorination system holds promise for advancing the chlorination industry and enhancing pharmaceutical production.