Graphene-based materials are highly interesting in virtue of their excellent chemical, physical and mechanical properties that make them extremely useful as privileged materials in different industrial applications. Sonochemical methods allow the production of low-defect graphene materials, which are preferred for certain uses. Graphene nanosheets (GNS) have been prepared by exfoliation of a commercial micrographite (MG) using an ultrasound probe. Both materials were characterized by common techniques such as X-ray diffraction (XRD), Transmission Electronic Microscopy (TEM), Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). All of them revealed the formation of exfoliated graphene nanosheets with similar surface characteristics to the pristine graphite but with a decreased crystallite size and number of layers. An exhaustive study of the particle size distribution was carried out by different analytical techniques such as dynamic light scattering (DLS), nanoparticle tracking analysis (NTA) and asymmetric flow field flow fractionation (AF4). The results provided by these techniques have been compared. NTA and AF4 gave higher resolution than DLS. AF4 has shown to be a precise analytical technique for the separation of GNS of different sizes.
Lithium-sulfur (Li-S) batteries have received enormous interest as a promising energy storage system to compete against limited, non-renewable, energy sources due to their high energy density, sustainability, and low cost. Among the main challenges of this technology, researchers are concentrating on reducing the well-known “shuttle effect” that generates the loss and corrosion of the active material during cycling. To tackle this issue, metal-organic frameworks (MOF) are considered excellent sulfur host materials to be part of the cathode in Li-S batteries, showing efficient confinement of undesirable polysulfides. In this study, MIL-88A, based on iron fumarate, was synthesised by a simple and fast ultrasonic-assisted probe method. Techniques such as X-ray diffraction (XRD), Raman spectroscopy, Thermogravimetric Analysis (TGA), Scanning Electron Microscopy (SEM), and N2 adsorption/desorption isotherms were used to characterise structural, morphological, and textural properties. The synthesis process led to MIL-88A particles with a central prismatic portion and pyramidal terminal portions, which exhibited a dual micro-mesoporous MOF system. The composite MIL-88A@S was prepared, by a typical melt-diffusion method at 155 °C, as a cathodic material for Li-S cells. MIL-88A@S electrodes were tested under several rates, exhibiting stable specific capacity values above 400 mAh g−1 at 0.1 C (1C = 1675 mA g−1). This polyhedral and porous MIL-88A was found to be an effective cathode material for long cycling in Li-S cells, retaining a reversible capacity above 300 mAh g−1 at 0.5 C for more than 1000 cycles, and exhibiting excellent coulombic efficiency.
A microporous carbon derived from biomass (almond shells) and activated with phosphoric acid was analysed as a cathodic matrix in Li–S batteries. By studying the parameters of the carbonization process of this biomass residue, certain conditions were determined to obtain a high surface area of carbon (967 m2 g−1) and high porosity (0.49 cm3 g−1). This carbon was capable of accommodating up to 60% by weight of sulfur, infiltrated by the disulphide method. The C–S composite released an initial specific capacity of 915 mAh g−1 in the Li–S cell at a current density of 100 mA g−1 with a high retention capacity of 760 mAh g−1 after 100 cycles and a coulombic efficiency close to 100%. The good performance of the composite was also observed under higher current rates (up to 1000 mA g−1). The overall electrochemical behaviour of this microporous carbon acting as a sulfur host reinforces the possibility of using biomass residues as sustainable sources of materials for energy storage.
An efficient lithium‐ion battery was assembled by using an enhanced sulfur‐based cathode and a silicon oxide‐based anode and proposed as an innovative energy‐storage system. The sulfur–carbon composite, which exploits graphene carbon with a 3 D array (3DG‐S), was synthesized by a reduction step through a microwave‐assisted solvothermal technique and was fully characterized in terms of structure and morphology, thereby revealing suitable features for lithium‐cell application. Electrochemical tests of the 3DG‐S electrode in a lithium half‐cell indicated a capacity ranging from 1200 to 1000 mAh g−1 at currents of C/10 and 1 C, respectively. Remarkably, the Li‐alloyed anode, namely, LiySiOx–C prepared by the sol–gel method and lithiated by surface treatment, showed suitable performance in a lithium half‐cell by using an electrolyte designed for lithium–sulfur batteries. The LiySiOx–C/3DG‐S battery was found to exhibit very promising properties with a capacity of approximately 460 mAh gS−1 delivered at an average voltage of approximately 1.5 V over 200 cycles, suggesting that the characterized materials would be suitable candidates for low‐cost and high‐energy‐storage applications.