During interventions to improve the energy efficiency of cultural heritage, it is common to use methodologies that are used for current buildings with different thermal behaviour. For this reason, research has been carried out on the thermal behaviour of old brick walls by carrying out thermal flow tests in the laboratory on brickwork specimens, in order to compare the behaviour of handmade bricks and mechanical bricks from more than a century ago, and to analyse the relationship between the values of thermal conductivity, humidity, density and porosity, as well as to compare these results with those obtained by applying the procedure of the EN-1745 standard. It was concluded that bricks behave thermally differently, depending on the manufacturing process: handmade or mechanical, in both types of brick it was found that the higher the moisture content and density were, the higher the brick’s thermal conductivity value. It has also been concluded that old bricks have thermal conductivity values different from those indicated in EN-1745 as a function of density, and that the ratio detected in these specimens in the dry state and in the wet state does not conform to the processes indicated in the standard. With regard to porosity, it is important to note that the greater the closed porosity, the lower the conductivity. It has been concluded that in order to intervene in cultural heritage buildings, it is necessary to carry out a specific study of the behaviour of the systems with which they were constructed.

Interventions in historic brick buildings require an exhaustive analysis of the current characteristics of bricks in order to establish the role performed by these elements in the buildings. This study presents the results of an experimental analysis of the compressive strength of brick specimens extracted from different buildings built in the 19th and 20th centuries in the province of Zamora (Spain). The study analyses specimens with very different characteristics to compare results from different masonry units and manufacturing processes. Specimens are classified into four groups according to their macroscopic and microscopic analyses. Compressive strength results are correlated to the above classification and to the results of density, absorption and open porosity of the samples. The compressive strength results present high variation between clay bricks (9.2–64.4 N/mm²) and between samples extracted from the same brick due to the heterogeneity of the material. Correlations between compressive strength and open porosity, absorption and dry density values are observed, with less dispersion in the case of high sintering level, up to 1000 °C. Finally, the compliance with the current Spanish Technical Building Code with respect to their compressive strength is checked.

STEAM (Science, Technology, Engineering, Arts and Mathematics) professions play a crucial role in transforming 21st-century society, as they contribute to developing new technologies that support the achievement of the Sustainable Development Goals (SDGs). Aligning engineering education with sustainable development requires raising awareness among students, fostering commitment among future generations of engineers, and promoting technical vocations. In this paper, an educational experience designed with these objectives is presented, in which more than 130 students from five undergraduate degrees in engineering and architecture at the Higher Polytechnic School of Zamora (HPSZ) of the University of Salamanca actively participated. To carry out the project, an online course was designed to train all participating students on general aspects of the 2030 Agenda, and research works were proposed in the ten involved degree subjects. The assessment of students' prior knowledge and learning regarding the 2030 Agenda was conducted through an objective multiple-choice pre-test and post-test. Additionally, their satisfaction with this educational experience was assessed through a questionnaire. The results revealed a considerable improvement in the students' knowledge of the general contents of sustainable development, especially after participating in classroom debate sessions. The initial objective test showed a low average score, indicating the lack of knowledge about the 2030 Agenda and the SDGs among engineering students. However, the final objective test revealed a significant improvement of 3 points out of 10. Regarding the research works, out of a total of 91 students, 53 papers addressing complex issues related to sustainable development and current engineering solutions were presented. This approach facilitated collaborative learning and the celebration of World Engineering Day at the HPSZ. The results of the satisfaction survey demonstrated that the experience was positive for both students and faculty Furthermore, its media impact was essential for increasing engineering vocations' visibility and social recognition.

This paper reports an experiment in the application of rubrics, as an assessment tool, in different degree courses in the fields of engineering and architecture. This paper involved five subjects, seven teachers, and a total of 170 students. We analyze the scores obtained by the students and the degree of satisfaction of both the students and teachers, based on questionnaires developed specifically for this purpose.