An improved method for preventing vortex rope formation and alleviating the associated pressure fluctuations in turbine draft tubes is investigated using baffles in the draft tube to hinder the swirling flow emerging from a Francis turbine runner. A strong swirl produces flow instabilities and pressure fluctuations. Partial load operating conditions at the rated water head and three flow rates are taken into consideration. It is demonstrated using a computational fluid dynamics simulation that this method effectively eliminates the vortex rope, particularly when using four baffles. The amplitude of the pressure pulsation in the draft tube modified with four baffles was 0.42 times that in a traditional draft tube. The baffles were found to reduce the tangential velocity of the flow in the draft tube and consequently hinder the development of the fierce swirling flow. This type of decrease is more significant compared to the gradual decay due to viscous effects of the solid wall in a traditional draft tube. The conclusion was verified by the results of experiments conducted using a novel device. The measured increase in turbine efficiency exceeded 3% at the evaluated partial loading point, indicating improved economic performance of the turbine.
15 January 2021 in KSCE Journal of Civil Engineering
Large-diameter buried steel pipes (BSPs) have been widely utilized in water diversion and hydropower fields. This paper presents a comprehensive numerical investigation on the interaction between the large-diameter pipe and soil under three typical working conditions, to capture the structural mechanical behaviors of pipe deformation, soil displacement, and soil pressure. Furthermore, a parametric analysis of pipe diameter is conducted, along with the sensitivity study of soil parameters based on the orthogonal test method. The results show that the water weight increases the pipe deformation significantly by 14%, while the high internal water pressure decreases the deformation greatly with the maximum effect of 39%. The pattern of soil pressure at the top of the pipe changes from parabola to double-hump as the pipe diameter varies from 0.5 m to 5.0 m. The pipe deformation and soil pressure keep increasing with the pipe diameter, but the safety margin for prism load decreases gradually. Pipe deformation and soil pressure are very sensitive to the elastic modulus and Poisson’s ratio of backfill. Friction coefficients of soil-soil (trench sidewall) and pipe-soil have great influences on the soil pressure, while the bedding material and backfill cohesion have small effects on it.
In engineering practice, the initial support system is commonly installed in the vicinity of the tunnel face after excavation, whereas the self-capacity of rock mass will fail to be utilized and the cost of the initial support system will be expensive. In this study, a methodology is proposed to determine the appropriate timing of initial support installation to find out the balance of tunnel safety and construction cost. Firstly, the global safety factor is introduced as the critical indicator to evaluate tunnel stability. Then, the comprehensive graphic relationship between the global safety factor and the distance to the tunnel face is established. Once the global safety factor decreases to an admissible value, the stability of the surrounding rock is in a critical state and the corresponding distance is the recommended location for installing the initial support. In these procedures, the installation time of the initial support at the typical tunnel section can be quickly designed and fed back by a direct indicator during construction. Meanwhile, several cases with different conditions have been carried out to discuss the regularity of the method.
Under the circumstances of rapid expansion of diverse forms of volatile and intermittent renewable energy sources, hydropower stations have become increasingly indispensable for improving the quality of energy conversion processes. As a consequence, Francis turbines, one of the most popular options, need to operate under off-design conditions, particularly for partial load operation. In this paper, a prototype Francis turbine was used to investigate the pressure fluctuations and hydraulic axial thrust pulsation under four partial load conditions. The analyses of pressure fluctuations in the vaneless space, runner, and draft tube are discussed in detail. The observed precession frequency of the vortex rope is 0.24 times that of the runner rotational frequency, which is able to travel upstream (from the draft tube to the vaneless space). Frequencies of both 24.0 and 15.0 times that of the runner rotational frequency are detected in the recording points of the runner surface, while the main dominant frequency recorded in the vaneless zone is 15.0 times that of the runner rotational frequency. Apart from unsteady pressure fluctuations, the pulsating property of hydraulic axial thrust is discussed in depth. In conclusion, the pulsation of hydraulic axial thrust is derived from the pressure fluctuations of the runner surface and is more complicated than the pressure fluctuations.
13 August 2018 in Latin American Journal of Solids and Structures
A spiral case with its steel spiral case (SSC) being embedded in reinforced concrete under a pressurized condition is called a preloaded filling spiral case structure (PFSCS) in a hydropower plant. As a steel-concrete composite structure, a PFSCS is designed to work reliably. The non-uniform gap and contact nonlinearity between the SSC and the surrounding mass concrete have a great effect on the bearing mechanism of the composite structure. However, the description of the gap and contact nonlinearity in a PFSCS is a tough work. With the aim of efficiently describing the evolution process of the non-uniform gap and contact nonlinearity, we performed an experimental investigation and proposed a novel numerical simulation technique for structural finite element analyses (FEA) of PFSCSs. In the technique, the gap and contact nonlinearity as well as the construction process and operation process of a PFSCS are taken into account. A friction-contact model is used to simulate the sliding of the SSC against the concrete. A plasticity damage model is employed to describe the concrete. The development of the gap, contact status between the steel liner and the surrounding concrete, stresses of the steel liner and the steel bars, as well as the concrete cracking time and crack pattern, are presented in this work. The FEA results agree well with the experimental results. The agreement provides evidence that the applicability and competence of the proposed technique are valid and satisfactory.