Enhancing the fracture strength and ductility of concrete through the incorporation of various types of synthetic and natural fibers with varying textures and contents remains challenging. Natural fibers, being versatile and eco-friendly construction materials, can be an excellent alternative to synthetic fibers. However, studies on natural fiber-reinforced (especially through the incorporation of jute fibers) novel composites like geopolymer binders remain deficient. Thus, the effects of various lengths (15, 25 and 35 mm) and volume contents (0.10, 0.20, 0.30, 0.40, 0.50, 0.60, and 0.70%) of natural jute fibers on the mechanical performance of fiber-reinforced geopolymer concrete were studied. The results revealed that jute fiber reinforcement remarkably affected the workability, compressive strength, fracture strengths, water absorption and microstructure properties of the proposed geopolymer concretes. Increasing the fiber length and volume fractions in the geopolymer matrix lowered the slump values and workability and increased the compressive strength. The specimen prepared with a fiber length of 35 mm and volume fractions of 0.70% displayed the lowest slump value (28 mm) and highest compressive strength (31.5 MPa) at 28 days. In addition, the specimens made with fiber volume fractions of 0.10, 0.20, 0.30, and 0.40% showed a significant improvement in the splitting tensile and flexural strengths. However, increasing the volume of the jute fibers up to 0.50% led to a slight drop in the fracture strength of the geopolymers. The specimens prepared with a length of 25 mm and a volume of 0.40% achieved the highest enhancement of splitting tensile strength (18.7%) and flexural strength (29.1%) at 28 days. In short, sustainable geopolymer concrete with high fracture performance can be obtained by incorporating natural jute fibers, leading to practical applications in the construction sector. The proposed green concrete may enable a reduction in solid waste, thus promoting a more sustainable concrete industry.
1 October 2013 in Advances in Structural Engineering
In order to study the residual stress distribution of the welded integral joint of steel truss bridge, a full-scale model was fabricated with the same welding process, same material as the real bridge in the bridge workshop. The residual stress state and distributions of residual stresses in the full-scale model were measured using blind-hole strain-gage method. The tested results show that high residual stress is caused during the welding process and the maximum tensile residual stress may reach the yield strength of the steel. Longitudinal tensile residual stress appears in the regions near the welding bead and changes to compressive stress at a certain distance from the welding bead, with the maximum tensile residual stress being in the centre of the welding bead. In butt-welding between two plates with different thicknesses, the value of welding residual stress in the thinner plate is lower than that of the thicker one. The results presented in this paper would be useful as references for developing measures of reducing the residual stress of integral joint in the fabrication of a real bridge.
Based on energy principle, the free vibration of orthotropic steel bridge deck is investigated. The orthotropic steel bridge deck considered to be a stiffened plate. Both longitudinal stiffeners and transverse diaphragms are considered to be beam elements according to the equivalent principle of mass and rigidity. Besides, the plate is analyzed according to classic thin plate theory. The mode shape functions are expressed by the product of two independent beam functions. During the derivation of frequency equation, the lateral flexural effect of both the plate and stiffeners is considered. Besides, the eccentricity and torsion of stiffeners are taken into consideration, as well as the membrane strain energy of the plate. The results of the present approach are validated by the published example. At last, a stiffened plate with three classical boundary conditions is studied. The results show good agreement with the FE software ANSYS. Besides, it is observed that the eccentricity of stiffeners has a greater influence on lower frequencies than the higher, and the dynamic rigidity of stiffened plate can be increased efficiently by increasing the thickness of longitudinal stiffeners or reducing the distance between neighboring stiffeners. But the latter is more efficient.
Current research on the stress mechanisms of composite connectors within steel–concrete structures of bridge towers is sparse, and there is a lack of established experimental methods and finite element modeling techniques for studying these mechanisms. This study focuses on a specific type of composite shear connector within the steel–concrete section of the Shunde Bridge tower. By employing proposed experimental methods and finite element model analysis, this research examines the load–slip curves and stress distribution of these shear connectors. It aims to elucidate the stress mechanisms and mechanical relationships between the composite connectors and the individual perforated plate connectors and shear stud connectors that comprise them. The results demonstrate that the proposed experimental methods and finite element modeling approaches effectively analyze the stress mechanisms of composite connectors, revealing that the ultimate load-bearing capacity and elastic stiffness of the composite connectors are approximately the sum of those of the individual connectors configured in parallel; The mechanical performance of the composite connectors in the steel–concrete section of the bridge tower is approximately the additive sum of the mechanical performances of the individual connectors comprising them. By comparing the experimentally measured load–slip curves with those calculated from the finite element models, it validates the modeling approach of the finite element model, and the material parameters established through material characteristic tests and literature review are reasonable.
Orthotropic steel decks (OSDs) serve as critical load-bearing components in long-span steel bridges, but high-amplitude welding residual stresses (WRSs) generated during the welding process pose significant threats to structural integrity. To mitigate these stresses, post-weld heat treatment (PWHT) has emerged as a promising technique. This investigation first establishes a semi-structural thermo-elasto-plastic finite element model of the Deck-U-rib-Diaphragm system with a six-pass welding sequence. The temperature field is modeled via a double-ellipsoidal heat source and birth–death element approach. Subsequently, thermo-mechanical coupling analysis is conducted to investigate the distribution characteristics of Von Mises residual stresses. The stress relief effect of PWHT is then explored by comparing different holding temperatures (T) and holding times (t), achieving a balance between stress reduction effectiveness and economic efficiency, when T = 550 °C and t = 40 min. Finally, full-scale experimental tests are designed, and the hole-drilling method is utilized to validate the numerical simulation results. This research provides valuable insights for the design of PWHT processes for OSDs.