Dalibor Petrovic

Dr. Dalibor Petrovic


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2022 in Vojnotehnicki glasnik
Verified
Journal Article
Open access
PDF file
ABAleksandar G. Bukvić
Aleksandar G. Bukvić
DPDalibor Petrovic
Dalibor Petrovic
IRIgor Z. Radisavljević
Igor Z. Radisavljević
SDSaša S. Dimitrić
Saša S. Dimitrić
Introduction/purpose: During exploitation tests of gasoline storage tanks, cracks can form in an austenitic-ferrite welded joint, which can compromise the entire tank. Methods: In order to obtain a welded joint of satisfactory strength and durability, the paper analyzes the influence of heat input on the tensile characteristics of welded joints. In the current literature and practice, additional materials for welding the tank elements are selected according to the chemical compositions of the elements of basic materials, with the help of the Schaeffler diagram. In this paper, the characteristics of welded joints of gasoline storage tanks are examined, when the largest part of the tank is made of fine - grained microalloyed steel NIOMOL 490 K, while the roof part of the tank is made of austenitic steel. Slabs of these two materials were welded by the MIG process with additional material MIG 18/8/6, at different amounts of heat input. Conclusion: The analysis of the results obtained by tensile testing according to SRPS EN ISO 6892-1: 2020 standard concluded that the behavior of the joint as a whole depends on the properties of each individual part of the welded joint and their mutual influence. It was also concluded that the mutual influence is better if welding is performed with a lower amount of heat input, because then a lower degree of mixing of additional material with basic materials is achieved.

16 January 2026 in Aerospace
Verified
Journal Article
Open access
PDF file
AKAleksandar Zdravko Knežević
Aleksandar Zdravko Knežević
BKBranimir B. Krstic
Branimir B. Krstic
ABAleksandar G. Bukvić
Aleksandar G. Bukvić
DPDalibor Petrovic
Dalibor Petrovic
Bosko RasuoBosko Rasuo
Bosko Rasuo
This research aims to characterize extended reality flight trainers and to provide a detailed account of the sensors employed to collect data essential for qualitative task performance analysis, with a particular focus on gaze behavior within the extended reality environment. A comparative study was conducted to evaluate the effectiveness of an extended reality environment relative to traditional flight simulators. Eight flight instructor candidates, advanced pilots with comparable flight-hour experience, were divided into four groups based on airplane or helicopter type and cockpit configuration (analog or digital). In the traditional simulator, fixation numbers, dwell time percentages, revisit numbers, and revisit time percentages were recorded, while in the extended reality environment, the following metrics were analyzed: fixation numbers and durations, saccade numbers and durations, smooth pursuits and durations, and number of blinks. These eye-tracking parameters were evaluated alongside flight performance metrics across all trials. Each scenario involved a takeoff and initial climb task within the traffic pattern of a fixed-wing aircraft. Despite the diversity of pilot groups, no statistically significant differences were observed in either flight performance or gaze behavior metrics between the two environments. Moreover, differences identified between certain pilot groups within one scenario were consistently observed in another, indicating the sensitivity of the proposed evaluation procedure. The enhanced realism and validated effectiveness are therefore crucial for establishing standards that support the formal adoption of extended reality technologies in pilot training programs. Integrating this digital space significantly enhances the overall training experience and provides a higher level of simulation fidelity for next-generation cadet training.

1 January 2023 in Vojnotehnicki glasnik
Verified
Journal Article
Open access
PDF file
ABAleksandar G. Bukvić
Aleksandar G. Bukvić
DPDalibor Petrovic
Dalibor Petrovic
IRIgor Z. Radisavljević
Igor Z. Radisavljević
SDSaša S. Dimitrić
Saša S. Dimitrić
Introduction/purpose: Constructions always have several critical points that can be sources of possible defects. All these critical places must be taken into account in safety assessment where the most unfavorable exploitation factors are considered and the local safety of a joint is assessed. Today, joints of various compositions are becoming more frequent in metal constructions. Due to the requirements of economy and ecology, welded joints of microalloyed ferritic steels with high-alloyed austenitic steels are increasingly encountered during the construction of power plants, chemical facilities, etc. Tests of such welded joints have been performed on tanks for oil derivatives, where parts of the tank shell are made of microalloyed ferritic steel and the roof structure is made of high-alloyed austenitic steel. Methods: In the paper, an experimental analysis of crack propagation in an austenitic-ferritic welded joint was performed. The welding was performed by the MIG welding process with two different heat inputs, and the same filler material MIG 18/8/6 was used. Two types of welded plates were tested. the characteristics of the base, filler and auxiliary materials and welding 16 technologies are given. Notched test specimens with an initiated crack-type fracture were made in order to determine the impact properties and fracture mechanics parameters. The results: The research carried out within this study aimed to compare the obtained results of the impact toughness and fracture toughness at flat deformation in a ferrite-austenitic welded joint. An evaluation of the results obtained during the testing of the experimental plates welded with different amounts of heat input is also given. Conclusion: These test results established the dependence of the geometry of a propagating crack and the stress conditions for further crack propagation. It is possible to determine the values of the parameters that describe the behavior of the material, both in linear-elastic and in elastoplastic fracture mechanics.