In this paper, a new single-phase cascaded multilevel inverter based on novel H-bridge units is proposed. In order to generate all voltage levels (even and odd) at the output, nine different algorithms are proposed to determine the magnitudes of dc voltage sources. Then, the proposed algorithms are compared to investigate their advantages and disadvantages. This topology is able to increase the number of output voltage levels by using a lower number of power electronic devices such as switches, power diodes, driver circuits, and dc voltage sources that lead to reduction in installation space and cost of the inverter. In addition, in the proposed cascaded multilevel inverter, not only the number of required power electronic devices is reduced, but also the amount of the blocked voltage by switches, and the number of different voltage amplitudes of the used sources is decreased. These features are some of the most important advantages of the proposed topology. These features are obtained via the comparison of the proposed topology and its proposed algorithms with the conventional cascaded multilevel inverters that have been presented in the literatures. The operation and performances of the proposed topology with its presented algorithms in generating all voltage levels have been verified by using the experimental results of a 49-level single-phase inverter.
28 February 2018 in IEEE Transactions on Power Electronics
In this paper, a high step-up quasi-Z Source (QZS) dc-dc converter is proposed. This converter uses a hybrid switched-capacitors switched-inductor method in order to achieve high voltage gains. The proposed converter have resolved the voltage gain limitation of the basic QZS dc-dc converter while keeping its main advantages, such as continuous input current and low voltage stress on capacitors. Compared to the basic converter, the duty cycle is not limited, and the voltage stress on the diodes and switch is not increased. In addition to these features, the proposed converter has a flexible structure, and extra stages could be added to it in order to achieve even higher voltage gains without increasing the voltage stress on devices or limiting the duty cycle. The operation principle of the converter and related relationships and waveforms are presented in the paper. Also, a comprehensive comparison between the proposed and other QZS based dc-dc converters is provided which confirms the superiority of the proposed converter. Simulations are done in power systems computer aided design (PSCAD) in order to investigate the maximum power point tracking (MPPT) capability of the converter. In addition, the valid performance and practicality of the converter are studied through the results obtained from the laboratory built prototype.
Multilevel inverters have attractive features which make them one of the most popular fields of investigations. They can operate in high power and high voltage conditions. Multilevel inverters generate output voltage with high quality and low harmonic contents. As the number of output voltage levels increases, the quality of the output voltage is improved leading to reduction of the filtering requirements. However, multilevel inverters have the disadvantage of increased power electronic switches. This leads to higher cost, size and complication. Some advanced topologies have been introduced to reduce the number of power electronic switches, unfortunately, most of these topologies need high voltage switches on their structure making them unsuitable for high voltage conditions. In this study, an innovative topology for multilevel inverter is proposed which reduces the number of switches considerably without using high voltage switches. The proposed topology is a general topology which can be extended for any number of voltage levels. The authors call this topology as cross‐switched multilevel inverter. The simulation results obtained in PSCAD/EMTDC as well as the experimental results verify the proposed topology.
23 February 2018 in IEEE Transactions on Industrial Electronics
In this paper, a new non-isolated high step-up dc-dc converter is proposed. Active-passive inductor cells (APICs) is used to extend the topology. The ability to achieve high gains is the main merit of the proposed topology. The proposed converter operates based on parallel charging and series discharging of the inductors. The converter also achieves high step-up voltage gain with appropriate duty cycle and low voltage and current stress on the power switches and diodes. The proposed converter is analyzed in operation modes. The main parameters of the converter such as voltage gain, voltage stress of semiconductor devices are calculated to compare with other structures in literature. Considering the output voltage ripple and filter size, the proposed converter is designed. Moreover, the losses and efficiency of the converter are calculated. The performance of the proposed converter is validated by experimental results.
The cascaded multilevel converters are the most favorable topologies of multilevel converters. However, they have the main disadvantage of using multiple independent dc voltage sources. This study proposes new cascaded multilevel converter topologies in which the number of independent dc voltage sources is reduced. In the proposed topologies, for a specific number of voltage levels, the number of dc voltage sources is halved. Beside the number of dc voltage sources, in one of the proposed topologies the number of switches is also reduced in comparison with that of the conventional cascaded multilevel converter. A new modified pulse‐width modulation method is presented to control the proposed topologies. Also, a method for compensating non‐ideality of the dc voltage sources is presented. Simulation results using PSCAD software as well as experimental results from a laboratory‐scale prototype are presented to verify the proposed multilevel converters.
17 August 2017 in IEEE Transactions on Power Electronics
In this paper, a new structure of nonisolated boost dc-dc converters based on voltage-lift technique is proposed. In comparison with conventional nonisolated boost dc-dc converters, the proposed converter generates higher voltage gain. In this paper, the relations between voltage and current of all elements in continuous conduction mode and discontinuous conduction mode are calculated as well as voltage gain in each mode. Then, the critical inductance and stress of switch current are extracted. Finally, the validity of given theories is examined by using the experimental results.