Much research and practical experience have shown that the utilization of textures has an enhancing effect on the performance of dynamic seals and the dynamic pressure lubrication of gas bearings. In order to optimize the performance of floating ring seals, this study systematically analyzes the effects of different texture shapes and their parameters. The Reynolds equation of the gas is solved by the successive over-relaxation (SOR) iteration method. The pressure and thickness distributions of the seal gas film are solved to derive the floating force, end leakage, friction, and the ratio of buoyancy to leakage within the seal. The effects of various texture shapes, including square, 2:1 rectangle, triangle, hexagon, and circle, as well as their parameters, such as texture depth, angle, and area share, on the sealing performance are discussed. Results show that the texture can increase the air film buoyancy and reduce friction, but it also increases the leakage by a small amount. Square textures and rectangular textures are relatively effective. The deeper the depth of the texture within a certain range, the better the overall performance of the floating ring seal. As the texture area percentage increases, leakage tends to increase and friction tends to decrease. A fractal roughness model is developed, the effect of surface roughness on sealing performance is briefly discussed, and finally the effect of surface texture with roughness is analyzed. Some texture parameters that can significantly optimize the sealing performance are obtained. Rectangular textures with certain parameters enhance the buoyancy of the air film by 81.2%, which is the most significant enhancement effect. This rectangular texture reduces friction by 25.8% but increases leakage by 79.5%. The triangular textures increase buoyancy by 28.02% and leakage increases by only 10.08% when the rotation speed is 15,000 r/min. The results show that texture with appropriate roughness significantly optimizes the performance of the floating ring seal.
High-speed segmented annular seals are often subjected to friction and wear, and the groove design on the sealing surface can effectively suppress this loss. For the purpose of improving the sealing performance, the segmented annular seal models of three structures are established, and the accuracy of the calculation model is verified by comparing with the previous results. Through fluid–solid–thermal coupled analysis, the flow field characteristics, opening characteristics, and leakage characteristics of the segmented annular seal under high working condition parameters were studied. The results show that the setting of the shallow groove forms the hydrodynamic effect by squeezing and hindering the flow of fluid in the clearance. The increase in rotational speed and pressure difference can promote the increase in the opening force, while the temperature has no significant effect on the opening of the seal. Seals with ladder-like grooves have the best opening performance, and seals without shallow grooves are already difficult to open under conditions of high pressure difference and large spring forces. Temperature and pressure difference are the main factors affecting the leakage of the seal, while the influence of the rotation speed is small. When the sealed pressure increases from 0.15 MPa to 0.4 MPa, the maximum increase in the leakage of the seal with specific groove design is 4.657 times the original. As the temperature rises from 420 K to 620 K, the maximum decrease in the three structures is up to 22.9%. Among the seals of the three structures, seals with ladder-like grooves have medium leakage. This research will contribute to the improvement of research methods for the sealing performance of segmented annular rings, especially for the evaluation of groove design and opening characteristics.
As a critical sealing component in aero-engines, the segmented annular seal is prone to friction and wear during the running-in stage, which seriously impairs its sealing performance and service life. To address this issue, this study takes the three-petal segmented annular seal made of T482 graphite as the research object, adopting a combined method of high-speed ring-block friction and wear tests and thermal–fluid–solid coupling simulation to investigate its friction and wear mechanisms and optimize its structural design. The results show that the segmented annular seal undergoes more severe friction and wear in the low-speed running-in stage; the wear rate increases with the rise in loading force and decreases with the increase in rotational speed, and the variation trend of surface roughness is consistent with that of the friction coefficient. Frictional heat and wear-induced scratches intensify the deformation and leakage of the seal, thereby leading to the risk of seal failure. Optimizing the depth of radial dynamic pressure grooves can significantly improve the opening performance of the seal, while optimizing the width of axial grooves mainly affects the seal leakage. This research provides a theoretical basis for improving the service life and sealing performance of segmented annular seals in aero-engines.