The automotive industry was always characterized by innovation and the use of cutting edge technology. Daily we can see vehicles packed with technological advancements. The main focus of the current technological trend is electric drives. With the rise in popularity of electric cars more types of vehicles are adapting electric drives. In the case of airplanes the standards are higher than in the case of cars so the emphasis of research and innovation is greater. This paper presents a list of the challenges electric aircrafts face and their potential solutions. Currently many of these problems currently only have partial solutions if any. There is also a comparison between the properties of materials used and the expectations for hybrid aircraft. A comprehensive model was created taking into account the criteria set for hybrid and electric aircraft. With the aid of the model the effect of the most important components on efficiency can be assessed.
This paper introduces a compact pneumatic artificial muscle (CPAM) that integrates a coaxial rod and an internal helical compression spring (stiffness 9750 N/m) into a McKibben-type outer muscle and compares it to a commercial DMSP-20-200N from FESTO Budapest, Hungary, with identical outer geometry and materials. Both actuators were mounted in a force-controlled test rig, pre-tensioned, and then cycled quasi-statically between their stretched and maximally contracted states at 13 internal pressures. For each pressure, median loading and unloading force–contraction curves were obtained from five repeats measuring both the cylinder excitation force and a load cell, and hysteresis was quantified by a normalized loop area based on peak force and common contraction range. Under the rated load of 2000 N at 0.6 MPa, the CPAM elongates less (−1.5% vs. −3%) and generates higher forces over most of the contraction range. The normalized hysteresis index of the CPAM is markedly lower at low pressures (≈0.05–0.25 MPa, reductions of about 10–25%), similar near 0.30 MPa, and slightly higher at 0.35–0.60 MPa (≈6–14%).
This paper’s goal is to introduce the third step of the EFOP-3.6.1-16-2016-00014. project on the Faculty of Engineering, University of Szeged. In this period the production technology of composite material was chosen and a fatigue test machine was developed and tested. The paper shortly describes the composite materials and summarizes the theory of fatigue than it presents the process of the development with several prototypes of fatigue test machine, some of which were manufactured and tested. Initially a shaker played the key role in the first two conceptions and finally a crank mechanism became as the best solution. The main solved problems during the development were selection of bearings and solving the partly dynamic balancing of the moving parts.
14 September 2016 in Recent Innovations in Mechatronics
Hardware in the loop testing is increasingly important product testing for cutting down time to market. In my previous article I identified the parameters of a DC motor control system using system identification. An implementation of the resulting transfer function was developed on an ARM based hardware in the loop system and has been verified against the original system. The results show that the hardware in the loop system produces responses within tolerance to the stimulus signals and can be used for testing of controlsystems.
In the realm of electronics, the foundational passive components—resistors, inductors, and capacitors—are well-established. However, in 1971, Leon Chua introduced a theoretical fourth element, the memristor, identified by its distinctive characteristic of memristance and its manifestation in a pinched hysteresis loop. This intriguing property suggests potential applications beyond conventional electronics, particularly in modelling hysteresis phenomena across various domains. This paper delves into the exploration of memristance as a mathematical framework for simulating hysteresis in electrical and mechanical systems. We commence by elucidating the theoretical underpinnings of memristance and its hysteresis behaviour, followed by a comprehensive overview of existing hysteresis models. Subsequently, we propose a novel approach that leverages the memristor model to offer enhanced insights and predictive capabilities for hysteresis in these systems. Through analytical examination and simulation studies, we demonstrate the versatility and applicability of the memristor model, underscoring its potential as a universal tool for hysteresis modelling. This research not only broadens the understanding of memristive properties but also opens new avenues for cross-disciplinary applications, ranging from electronic circuit design to mechanical system analysis.