Solange S. Magalhães

Dr. Solange S. Magalhães


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 July 2025 in Gels
Verified
Journal Article
Open access
PDF file
FAFrancisca Araújo
Francisca Araújo
SMSolange S. Magalhães
Solange S. Magalhães
Bruno MedronhoBruno Medronho
Bruno Medronho
Alireza EivaziAlireza Eivazi
Alireza Eivazi
CDChristina Dahlström
Christina Dahlström
Luís AlvesLuís Alves
Luís Alves
Chitosan films with potential application in triboelectric nanogenerators (TENGs) represent a promising approach to replace non-biobased materials in these innovative devices. In the present work, chitosan with varying molecular weights (MW) and degrees of deacetylation was dissolved in aqueous acetic acid (AA) at different acid concentrations. It was observed that the MW had a greater influence on the viscosity of the solution compared to either the acid concentration or deacetylation degree. Gel formation occurred in high-MW chitosan solutions prepared with low AA concentration. Films prepared from chitosan solutions, through solvent-casting, were used to prepare TENGs. The power output of the TENGs increased with higher concentrations of AA used in the chitosan dissolution process. Similarly, the residual AA content in the dried films also increased with higher initial AA concentrations. Additionally, hot-pressing of the films significantly improves the TENG power output due to the decrease in morphological defects of the films. It was demonstrated that a good selection of the acid concentration not only facilitates the dissolution of chitosan but also plays a key role in defining the properties of the resulting solutions and films, thereby directly impacting the performance of the TENGs.

11 October 2025 in Sustainability
Verified
Journal Article
Open access
PDF file
SMSolange S. Magalhães
Solange S. Magalhães
Luís AlvesLuís Alves
Luís Alves
Bruno MedronhoBruno Medronho
Bruno Medronho
ISIda Svanedal
Ida Svanedal
MNMagnus Norgren
Magnus Norgren
Maria Graca RasteiroMaria Graca Rasteiro
Maria Graca Rasteiro
Microplastic pollution represents a significant environmental challenge, as microplastics accumulate in effluents and soils, causing serious risks to ecosystems and human health. Efficient removal of these contaminants is essential to mitigate their potential adverse effects. This review summarizes and critically analyses current methods for the removal of microplastics from effluents and soils, focusing on their effectiveness, advantages, and limitations. Conventional techniques—including filtration, flotation, chemical coagulation, flocculation, and adsorption—are discussed in the context of wastewater treatment and soil remediation. Emerging approaches, such as flocculation processes with special focus on the application of bio-based flocculants, are also highlighted as promising solutions. Key challenges in microplastic removal, including the diversity of microplastic types, their small size, and the complexity of environmental matrices, are addressed. This work intends to contribute to the urgent need for further research to develop more efficient and sustainable strategies for microplastic removal from environmental systems.

3 November 2026 in Polymers
Verified
Journal Article
Open access
PDF file
SMSolange S. Magalhães
Solange S. Magalhães
María José Aliaño-GonzálezMaría José Aliaño-González
María José Aliaño-González
SLSofia Leão
Sofia Leão
MOMargarida Oliveira
Margarida Oliveira
INInês Pereira das Neves
Inês Pereira das Neves
Maria Graca RasteiroMaria Graca Rasteiro
Maria Graca Rasteiro
Deep eutectic solvents (DESs) are versatile media for lignocellulosic biomass fractionation, but their practical relevance depends on whether they remain effective across feedstocks of very different structure and composition. In this study, DESs composed of levulinic acid and choline chloride (LA:ChCl) at molar ratios of 2:1 and 3:1 were applied to two structurally distinct lignocellulosic sources, Acacia wood and sugarcane bagasse, to assess the applicability of the same solvent system to feedstocks of contrasting structure rather than its performance on a single substrate. Extractions were performed at 120, 140, and 160 °C for 1, 2, 4, 6, and 8 h, and process performance was assessed through recovered solid yield and total lignin content in the recovered solid fraction obtained after DES treatment followed by alkaline washing. The combined DES treatment and subsequent alkaline washing resulted in substantial lignin removal from both feedstocks, although the individual contribution of each treatment step could not be determined. For Acacia wood, recovered solid yields of up to 89.20 ± 0.07% and lignin contents as low as 0.94 ± 0.21% were achieved, while for sugarcane bagasse a 67.48 ± 0.15% recovered solid yield and 1.32 ± 0.77% total lignin content were obtained at a 3:1 ratio, 140 °C, and 6 h. A four-factor multivariate analysis revealed a significant Feedstock × Ratio × Time × Temperature interaction, indicating that, although the solvent was effective for both types of biomass, the operational window that maximizes its performance must be tuned to the specific feedstock: Acacia wood exhibited a pronounced trade-off between solid recovery and lignin removal, whereas sugarcane bagasse allowed relatively high recovered solid yields and low lignin contents to be achieved simultaneously. Overall, these results demonstrate the applicability of the LA:ChCl-based fractionation process, including subsequent alkaline washing, to the two structurally distinct feedstocks investigated, while highlighting the need to determine the individual contribution of each treatment step.

30 August 2026 in Macromol
Verified
Journal Article
Open access
PDF file
SMSolange S. Magalhães
Solange S. Magalhães
MOMargarida Oliveira
Margarida Oliveira
CVCátia Venâncio
Cátia Venâncio
Isabel M. LopesIsabel M. Lopes
Isabel M. Lopes
Luís AlvesLuís Alves
Luís Alves
MNMagnus Norgren
Magnus Norgren
Flocculation is a physicochemical process with critical relevance to industrial and environmental operations, including potable water production, wastewater remediation, mineral processing, papermaking, and food manufacturing. The efficiency of flocculation is determined by the chemical nature, molecular structure, and physicochemical interactions of flocculants with suspended colloidal matter. Conventional synthetic polyacrylamides, available in nonionic, anionic, and cationic forms, function predominantly via electrostatic neutralization, polymer chain bridging, and sweep flocculation induced by precipitated hydroxides. Their high molecular weight, customizable charge density, and cost-effectiveness have consolidated their industrial dominance. However, the inherent resistance of polyacrylamides to biodegradation in combination with its monomer’s toxicity and increasing regulatory pressure have accelerated research toward sustainable alternative materials. Recent developments include functionalized natural polysaccharides (e.g., chitosan, cellulose derivatives, starch esters), bio-based copolymers, and nanoengineered hybrid systems incorporating inorganic domains to enhance colloid destabilization and sedimentation kinetics. This review systematically examines the physicochemical principles underlying flocculation, evaluates the performance parameters and limitations of polyacrylamides, and highlight emerging strategies for sustainable flocculant design. Prospects for the next generation of flocculation technologies are discussed in the context of mechanistic optimization, ecological safety, and compliance with evolving environmental regulations.