One of the most challenging problems for people around the world is the lack of clean water. In the past few decades, the massive discharge of emerging organic pollutants (EOPs) into natural water bodies has exacerbated this crisis. Considerable research efforts have been devoted to removing these EOPs due to their biotoxicity at low concentrations. Heterogeneous photocatalysis via coupling clay minerals with nanostructured semiconductors has proven to be an economical, efficient, and environmentally friendly technology for the elimination of EOPs in drinking water and watershed water. Natural zeolite minerals (especially clinoptilolites) are regarded as appropriate supports for semiconductor-based photocatalysts due to their characteristics of having a low cost, environmental friendliness, easy availability, co-catalysis, etc. This review summarizes the latest research on clinoptilolites used as supports to prepare binary and ternary metal oxide or sulfide semiconductor-based hybrid photocatalysts. Various preparation methods of the composite photocatalysts and their degradation efficiencies for the target contaminants are introduced. It is found that the good catalytic activity of the composite photocatalyst could be attributed to the synergistic effect of combining the clinoptilolite adsorbent with the semiconductor catalyst in the heterogeneous system, which could endow the composites with an excellent adsorption capacity and produce more e⁻/h⁺ pairs under suitable light irradiation. Finally, we highlight the serious threat of EOPs to the ecological environment and propose the current challenges and limitations, before putting the zeolite mineral composite photocatalysts into practice. The present work would provide a theoretical basis and scientific support for the application of zeolite-based photocatalysts for degrading EOPs.

Gas sensors based on metal oxide semiconductors (MOS) have been widely used for the detection and monitoring of flammable and toxic gases. In this paper, p-type Cr₂O₃ and Ti-doped Cr₂O₃ (CTO) thin films were synthesized using an aerosol-assisted chemical vapor deposition (AACVD) method. Detailed analysis of the thin films deposited, including structural information, their elemental composition, oxidation state, and morphology, was investigated using XRD, Raman analysis, SEM, and XPS. All the gas sensors based on pristine Cr₂O₃ and CTO exhibited a reversible response and good sensitivity to isobutylene (C₄H₈) and ammonia (NH₃) gases. Doping Ti into the Cr₂O₃ lattice improves the response of the CTO-based sensors to C₄H₈ and NH₃. We describe a novel mechanism for the gas sensitivity of p-type metal oxides based on variations in the oxygen vacancy concentration.

Ni-based catalysts have been widely used in catalytic reactions by researchers due to their advantages such as abundant resources, high catalytic activity and lower prices than precious metals. However, the problems of easy agglomeration and poor dispersion of Ni-based catalysts have hindered their large-scale application. Therefore, it is necessary to select a suitable preparation method to reduce the agglomeration of the catalyst and improve its dispersion. In this paper, the Ni-NiAl₂O₄/tourmaline composite material was prepared by using the microwave hydrothermal reduction method. The most favorable conditions for preparing NiAl₂O₄/tourmaline are as follows: using TEOA as the additive, the microwave hydrothermal temperature is 220 °C, the calcination temperature is 800 °C, and the addition amount of tourmaline is 7.4 wt.%. NiAl₂O₄ has a good dispersion over the surface of tourmaline support and the optimal NiAl₂O₄/tourmaline catalyst exhibits a specific surface area of 106.5 m²/g. Metallic nickel was reduced at 650 °C to further obtain Ni-NiAl₂O₄/tourmaline composites. Finally, the Ni-NiAl₂O₄/tourmaline composites showed significantly improved catalytic dry reforming of methane (DRM) activity compared to Ni-NiAl₂O₄ sample under low-temperature conditions (500–600 °C), meaning that the tourmaline carrier could effectively optimize the low-temperature catalytic performance of Ni-NiAl₂O₄.

There was an error in the original publication

The oxygen evolution reaction (OER), serving as the anodic bottleneck in electrochemical water splitting for hydrogen production, severely limits the overall energy conversion efficiency due to its sluggish kinetics. Developing efficient and stable electrocatalysts based on earth-abundant elements is a critical challenge for advancing clean energy technologies. In recent years, silicate materials have demonstrated significant potential in alkaline OER catalysis owing to their unique stable silicon-oxygen tetrahedral framework and flexibly tunable metal-oxygen-silicon electronic coordination environments. This review systematically summarizes recent progress in silicate-based materials, including natural clay mineral supports such as halloysite, for OER electrocatalysis. It focuses on controllable synthesis strategies for silicate materials and provides an in-depth analysis of the regulation mechanisms for their electronic structure and surface properties through defect engineering, anion vacancy construction, and bimetallic/non-metallic heteroatom doping. Particular emphasis is placed on research pathways that utilize natural silicate clay minerals as both supports and silicon sources to construct high-performance composite catalytic materials via innovative structural design and interface engineering. Systematic studies indicate that precisely modulated silicate-based catalysts exhibit excellent electrochemical activity and long-term stability in the alkaline OER process. This review offers perspectives on the future development of efficient and stable silicate-based catalytic systems for renewable energy conversion.