We present a simulation strategy using ATLAS-2D to optimize the back-contact hole grid (i.e., size and pitch of openings) of the Al 2 O 3 -rear-passivation layer in ultrathin Cu(In,Ga)Se 2 photovoltaic cells. We first discuss and compare our simulation model with a series of experimental nonpassivated and passivated cells to decouple the crucial passivation parameters. The simulation results follow the experimental trends, highlighting the beneficial effects of the passivation on the cell performances. Furthermore, it stresses the influence of the passivation quality at the Al 2 O 3 /Cu(In,Ga)Se 2 (CIGS) interface and of the contact resistance at the Mo/CIGS interface within the openings. Further simulations quantify significant improvements in short-circuit current and open-circuit voltage for different sizes of openings in the Al 2 O 3 layer, relative to an excellent passivation quality (i.e., high density of negative charges in the passivation layer). However, a degradation is predicted for a poor passivation (i.e., low density of such charges) or a high contact resistance. Consequently, we point out an optimum in efficiency when varying the opening widths at fixed hole-pitch and fixed contact resistance. At equivalent contact resistance, simulations predict that the sizes of the pitch and openings can be increased without optimal performance losses when maintaining a width to pitch ratio around 0.2. This simulation trends have been confirmed by a series of experiments, indicating that it is crucial to care about the dimensions of the opening grid and the contact resistance of passivated cells. These simulation results provide significant insights for optimal cell design and characterizations of passivated UT-CIGS PV cells.
Hierarchical textures (combining 2D periodic large and small micro textures) as an external outcoupling solution for OLEDs have been researched, both experimentally and by optical simulations. For the case of a red bottom emitting OLED, different hierarchical textures were fabricated using laser-based methods and a replication step and applied to the OLED substrate, resulting in an increased light outcoupling. Laboratory-size OLED devices with applied textured foils show a smaller increase in efficiency compared to the final large area devices. The results show that the full exploitation of textured foils in laboratory-size samples is mainly limited by the lateral size of the thin film stack area and by limited light collection area of the measuring equipment. Modeling and simulations are used to further evaluate the full prospective of hierarchical textures in large area OLED devices. Optimization of hierarchical textures is done by simultaneously changing the aspect ratios of the small and large textures and a potential of 57% improvement in EQE compared to devices without applied textures is predicted by simulations. Optimized hierarchical textures show similar outcoupling efficiencies compared to optimized single textures, while on the other hand hierarchical textures require less pronounced features, lower aspect ratios, compared to single textures to achieve the same efficiencies. Hierarchical textures also help in eliminating flat parts that limit outcoupling efficiency. Finally, the limiting factors that prevent higher outcoupling are addressed. We show that the dominant factor is non-ideal reflection from the organic thin film stack due to parasitic absorption. In addition, possible ways to further increase the outcoupling from a thick substrate are indicated.
The detection of biomolecules based on fluorescence measurements is a powerful diagnostic tool for the acquisition of genetic, proteomic and cellular information. One key performance limiting factor remains the integrated optical filter, which is designed to reject strong excitation light while transmitting weak emission (fluorescent) light to the photodetector. Conventional filters have several disadvantages. For instance absorbing filters, like those made from amorphous silicon carbide, exhibit low rejection ratios, especially in the case of small Stokes’ shift fluorophores (e.g. green fluorescent protein GFP with λexc = 480 nm and λem = 510 nm), whereas interference filters comprising many layers require complex fabrication. This paper describes an alternative solution based on dielectric diffraction gratings. These filters are not only highly efficient but require a smaller number of manufacturing steps. Using FEM-based optical modelling as a design optimization tool, three filtering concepts are explored: (i) a diffraction grating fabricated on the surface of an absorbing filter, (ii) a diffraction grating embedded in a host material with a low refractive index, and (iii) a combination of an embedded grating and an absorbing filter. Both concepts involving an embedded grating show high rejection ratios (over 100,000) for the case of GFP, but also high sensitivity to manufacturing errors and variations in the incident angle of the excitation light. Despite this, simulations show that a 60 times improvement in the rejection ratio relative to a conventional flat absorbing filter can be obtained using an optimized embedded diffraction grating fabricated on top of an absorbing filter.
Tandem solar cells present a promising solution to overcome the Schottky–Queisser efficiency limit of single-junction solar cells. In this article, an all–thin-film tandem solar cell based on perovskite (PK) top cell and chalcopyrite Cu (In, Ga) Se2 (CIGS) bottom cell is researched. Device optical simulations are validated on the top and bottom cells and employed for the analysis of PK/CIGS tandem cells. In particular, the optical effects of introduced laser reduced graphene oxide (rGO) layers at two positions in the tandem cell: 1) at the position between the top PK and bottom CIGS cell and 2) underneath the front transparent electrode. The purpose of introducing rGO layers is to improve the optoelectrical properties of the device, based on the tunable electronic and optical characteristics of rGO layers. Optical simulation results show that the parasitic absorption in rGO layers may noticeably affect the optical performance of the tandem cell if the layers are not optimized. The use of a thin and a few nanometer-thick rGO is suggested from the analysis if its parasitic absorption is not reduced. Directions for further optimization of optical rGO, including the reduction of parasitic absorption and tuning of the real part of the refractive index, are performed.