An implicit generalized predictive self-correction controller (IGPC) is proposed in this paper to suppress the force ripple of switched reluctance linear motors (SRLMs). Due to its good robustness and rolling optimization features, the dynamic matrix controller (DMC), a kind of multi-step model predictive controller, is considered an effective method to suppress the force ripple of SRLMs. However, because DMC uses a fixed predictive model, it has high requirements for the accuracy of the predictive model, and the non-linear SRLMs make it difficult to adapt to different loads. To ease this problem, the IGPC proposed in this paper adopts a more flexible predictive model and improves the generalized predictive controller (GPC) to avoid solving the Diophantine equation online, which can adapt to different loads and reduce the system's burden. Besides, the proposed IGPC reduces the computational burden during matrix operations compared to DMC. In the simulation and experimental test based on a 100W 6/4 double-sided SRLM (DSRLM), the proposed IGPC is compared with DMC, and the force distribution function (FDF) adopts the current hysteresis, the results show that the proposed IGPC a better force ripple suppressing performance and has better load capacity compared with DMC.
14 August 2025 in IEEE Transactions on Power Electronics
This article proposes a wireless power transfer system based on hybrid self-switching of coupled inductor that not only realizes constant current (CC)/constant voltage (CV) output but also effectively copes with a variety of abnormal working conditions in the charging process by switching on the secondary side. First, the LCC-LCC/S self-switching composite topology is presented, and the CC/CV switching is achieved by utilizing a coupled inductor with a center tap based on the LCC compensation topology. The working principle of the CC/CV topology and the parameter calculation flow are analyzed in detail. Subsequently, the impedance, output characteristics, and switching characteristics of the CC/CV topology are simulated and analyzed. In addition, the topology’s stability under abnormal working conditions, such as the missing adjacency, load short-circuit, and load open-circuit, is analyzed. Finally, an experimental platform is constructed with the objective of verifying the feasibility and effectiveness of the proposed scheme. The experimental results demonstrate that the proposed charging system exhibits excellent CC and CV output characteristics without the need for additional inductor capacitance. The proposed system has a maximum output efficiency of 89.6%, a maximum current of 5.3 A, and a maximum voltage of 23 V, which fully meets the requirements of CC and CV wireless charging.
12 December 2022 in IEEE Transactions on Transportation Electrification
This paper presents a new power converter topology that enables reconfigurable winding operation in a double stator axial flux switched reluctance motor (DSAFSRM). The proposed power converter allows the winding working in series and parallel connection methods and requires fewer components. By applying the reconfigurable winding converter and implementing the mode selection scheme, both the wide speed range of the parallel mode and the high efficiency of the series mode are obtained, thus achieving high-efficiency operation over a wide speed range. At first, the topology and operating modes are introduced. The six available working states are also detailed. Then the drive system simulation model with the reconfigurable winding power converter is established in the MATLAB/Simulink environment. The steady-state performance of the two modes and the dynamic switching performance are simulated and analyzed. Finally, the DSAFSRM drive based on the reconfigurable winding converter is built and experimentally tested. The performance results verify the validity and correctness of the presented power converter.
11 February 2020 in IET Electric Power Applications
This study presents a non‐linear modelling method for a switched reluctance linear machine (SRLM), which achieves high modelling precision while requiring no prior knowledge regarding the specific structural dimensions of an SRLM. The proposed modelling method provides accurate flux linkage data based on limited experimental measurements through an interpolation process using a variant sigmoid function. The accuracy of the interpolation process is further increased by considering mutual coupling among the three phases. The performance of the proposed method is validated experimentally by comparing it with the performances of the Fourier series method and the two‐dimensional finite element method. The results demonstrate that the proposed method achieves greater modelling precision than the other methods considered in modelling an SRLM.
This paper deals with rotor position estimation of switched reluctance motors (SRM). The estimation method can be applied in SRM sensorless control of position speed and torque controllers. The implementation suggested is based on a real time adaptive filter. The measured variables are supply voltage and stator currents. These currents are used repeatedly for rotor position estimation by using linear adaptive filter which time constant is adjusted to the speed of the rotor. The result of this estimation is a rather precise and convenient rotor angle determining device for SRM sensorless control electrical drives.
The indoor air quality significantly impacts human health, and monitoring it in real time is essential for ensuring safe living environments. This paper presents AtmoCell, an advanced, low-power air-quality monitoring node designed for home use. The system integrates a CCS811 gas sensor for detecting volatile organic compounds and CO 2 , a BME280 sensor for monitoring temperature, humidity, and pressure, and a ferroelectric random access memory based microcontroller for energy-efficient data logging. The device utilizes an ESP32 for wireless connectivity and real-time data transmission. With modularity in mind, and a focus on low-power operation and compact design, AtmoCell offers an affordable, scalable solution for continuous air quality monitoring in residential settings, aligning with current health and environmental standards.