In the present work, the mechanical and tribological properties of carbon nanotube (CNT)-reinforced Cu matrix composites featuring 0–1.8 vol% CNTs prepared by spark plasma sintering under dry sliding and boundary lubrication conditions were investigated. The results of microstructure revealed that the bonding interface in Cu/CNT composites was very well established. Additionally, the addition of CNTs has a positive effect on improving the hardness and tensile strength of the composites, while the stress–strain response quasi-static tensile test confirms the same results. CNTs are proved to lead to certain self-lubrication. The addition of CNTs could result in decreased coefficient of friction (COF) and wear rates by reducing adhesive wear under dry sliding conditions, while the oil lubricating film was the major reason for decreased COF under boundary lubrication conditions.
Electromagnetic rail launch technology has attracted increasing attention owing to its advantages in terms of range, firepower, and speed. However, due to electricity-magnetism-heat-force coupling, the surface of the armature–rail friction pair becomes severely damaged, which restricts the development of this technology. A series of studies have been conducted to reduce the damage of the armature–rail friction pair, including an analysis of the damage mechanism and protection strategies. In this study, various types of surface damage were classified into mechanical, electrical, and coupling damages according to their causes. This damage is caused by factors such as mechanical friction, mechanical impact, and electric erosion, either individually or in combination. Then, a detailed investigation of protection strategies for reducing damage is introduced, including material improvement through the use of novel combined deformation and heat treatment processes to achieve high strength and high conductivity, as well as surface treatment technologies such as structural coatings for wear resistance and functional coatings for ablation and melting resistance. Finally, future development prospects of armature–rail friction pair materials are discussed. This study provides a theoretical basis and directions for the development of high-performance materials for the armature–rail friction pair.
A sensitivity analysis of braking speed and normal load on tribological properties of copper metal matrix composites (Cu-MMCs) was investigated using a subscale dynamometer. The morphologies of the worn surface and subsurface were observed by a scanning electron microscope and 3D video microscope. The results indicated that temperatures on the Cu-MMC surface increased with increasing the braking speed and normal load. The average coefficient of friction gradually decreased as the braking speed or normal load increased, and a slight decrease in the wear rate with increasing the braking speed up to 17 m/s after which a clear increasing trend was observed. As the normal load increased from 612 N to 1836 N, the wear rate decreased firstly and then promptly decreased. The transition in wear mechanism of Cu-MMC significantly depended on braking speed and normal load.
A series of Al2O3–Al2TiO5 ceramic composites with different Al2TiO5 contents (10 and 40 vol.%) fabricated at different sintering temperatures (1450 and 1550 °C) was studied in the present work. The microstructure, crystallite structure, and through-thickness residual stress of these composites were investigated by scanning electron microscopy, X-ray diffraction, time-of-flight neutron diffraction, and Rietveld analysis. Lattice parameter variations and individual peak shifts were analyzed to calculate the mean phase stresses in the Al2O3 matrix and Al2TiO5 particulates as well as the peak-specific residual stresses for different hkl reflections of each phase. The results showed that the microstructure of the composites was affected by the Al2TiO5 content and sintering temperature. Moreover, as the Al2TiO5 grain size increased, microcracking occurred, resulting in decreased flexure strength. The sintering temperatures at 1450 and 1550 °C ensured the complete formation of Al2TiO5 during the reaction sintering and the subsequent cooling of Al2O3–Al2TiO5 composites. Some decomposition of AT occurred at the sintering temperature of 1550 °C. The mean phase residual stresses in Al2TiO5 particulates are tensile, and those in the Al2O3 matrix are compressive, with virtually flat through-thickness residual stress profiles in bulk samples. Owing to the thermal expansion anisotropy in the individual phase, the sign and magnitude of peak-specific residual stress values highly depend on individual hkl reflection. Both mean phase and peak-specific residual stresses were found to be dependent on the Al2TiO5 content and sintering temperature of Al2O3–Al2TiO5 composites, since the different developed microstructures can produce stress-relief microcracks. The present work is beneficial for developing Al2O3–Al2TiO5 composites with controlled microstructure and residual stress, which are crucial for achieving the desired thermal and mechanical properties.
Fe and Cr are regarded as two of the most important friction components in Cu-based composites (Cu–BCs). In this study, the microstructural detection and micro- and macro-tribology evaluation of Cu–BCs containing Fe and Cr were performed. The results indicated that both Fe and Cr formed diffusion interfaces with the copper matrix. Because of the generation of a defect interface layer, the Cr/Cu interface exhibited a low bonding strength. Owing to the excellent binding interface between Fe and Cu, the high coefficient of friction (COF) of Fe, and the formation of a mechanical mixing layer promoted by Fe, the Cu–BCs containing Fe presented better friction performance under all braking energy per unit area (BEPUA) values. The main wear mechanism of Cu–BCs containing Fe and Cr changed from abrasion to delamination with an increase in BEPUA, and the delamination of Cu–BCs containing Fe was induced by breaks in the mechanical mixed layer (MML).
It is limited to use cellulose nanocrystals (CNCs) as green lubricant nanoadditives due to their high biodegradability. A promising solution is to convert CNCs into biocarbon. Herein, a multi-layer biocarbon (MLC) was prepared by carbonizing CNCs with an ionic liquids–thermal method. MLC was characterized comprehensively and then dispersed into rapeseed oil for use as a nanoadditive. The tribological performance of the MLC nanoadditive was evaluated using a ball-on-disc tribometer. The lubrication mechanism of the MLC nanoadditive was elucidated according to wear analysis of the worn surfaces and wear residues. It was found that MLC had a high carbon content of 77 at% and showed a two-dimensional multi-layered morphology. Each layer was composed of amorphous carbon nanosheets embedded with many crystalline carbon dots. The MLC nanoadditive was of excellent dispersibility and stability in rapeseed oil. Tribological experiments showed that the MLC nanoadditive, with a concentration of merely 0.04 wt%, led to a decrease in the frictional coefficient by 12.4% and the wear volume by 50.7%, having higher efficacy than the CNC nanoadditive. The exceptional lubrication effect of the MLC nanoadditive was mainly attributable to its interfacial deposition behavior and its subsequent fragmenting behavior. This work develops a novel method for biocarbon preparation and showcases its significant potential in lubrication applications.