Microfiltration (MF) and ultrafiltration (UF) membranes are capable of rejecting most of particulate and colloidal matter from natural water. The major impediment to their applications is fouling caused by contaminants that accumulate on and/or inside the membrane. Therefore, most membranes are subjected to chemical cleaning procedures as one of the methods to control fouling. Exposure to chemical cleaning agents can reduce the performance and lead to the degradation of polyethersulfone (PES) ultrafiltration membranes. This study was conducted in order to evaluate the effect of cleaning agents on the properties of the PES membranes during exposure to short-term foulant and a cleaning agent. The cleaning agents evaluated were NaOH, HCl and NaOCl. The accelerated static cleaning conditions showed significant changes in PES flat sheet membrane properties in case of cleaning with NaOCl. These changes were analyzed using SEM microscopy, FTIR spectroscopy, contact angle measurement and hydraulic membrane performance evaluation.
Austenitic stainless steels are used widely in many fields due to their good mechanical properties and high resistance to corrosion. This work focuses on the reconstruction of the passive film after scratching. The purpose of the study was to compare changes in the rate of passive layer reconstruction and to discuss the effect of both the type of material and its electrochemical treatment on the reconstruction of the passive layer for two types of stainless steel: 304 and 316. The XPS tests performed indicate a significantly higher Cr/Fe ratio for the samples after the electropolishing process of 1.41–1.88 compared to the as-received samples of 0.82–0.86. After 2–3 min of sputtering the surface with Ar+ ions, a decrease in chromium content can be observed, with a simultaneous increase in nickel content, visible especially for the electropolished samples. A new approach in the conducted research was to scratch the test samples under controlled conditions, then evaluate the dynamics of the passive layer reconstruction using the AFM method, and then confront the obtained results with XPS measurements for the corresponding samples. For the as-received samples (2B finish) and those after surface treatment, regardless of the level of contamination of the electropolishing process bath, the reconstruction time was similar, which was approximately 2 h, although certain differences in the process dynamics were noticeable.
26 September 2017 in Journal of Water and Land Development
The municipal sludge characterized non-Newtonian behaviour, therefore the viscosity of the sewage sludge is not a constant value. The laboratory investigation was made using coaxial cylinder with rotating torque and gravimetric concentration of the investigated sludge ranged from 4.40% to 2.09%. This paper presents the investigation on the effect of concentration of rheological sludge behaviour. The three different rheological models: Bingham (plastic model), Ostwald-de Waele (power-law), Hershel-Bulkley’s were calculated by fitting the experimental data of shear stress as a function of shear rate to these models. In this study, the 3-parameter Herschel- Bulkley’s model fits the experimental data best.
In this work, the removal of NOM (natural organic matter) as represented by humic acid by means of electrospun nanofiber adsorptive membranes (ENAMs) is described. Polyacrylonitrile (PAN) was used for the preparation of ENAMs incorporating silica nanoparticles as adsorbents. The addition of silica to the polymer left visible changes on the structural morphology and fibers’ properties of the membrane. The membrane samples were characterized by pure water permeability, contact angle measurement, SEM, XPS, and XRD. This study assesses the preliminary performance of PAN-Si membranes for the removal of natural organic matter (NOM). The membrane rejected the humic acid, a surrogate of NOM, from 69.57% to 87.5%.
The technology based on electrospun membranes exhibits great potential in water treatment. This study presents experimental data involving the fabrication of nanofiber membranes with powdered activated carbon (PAC) and its application for the removal of natural organic matter. The fabricated membrane materials were characterized using various techniques. These include scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and X-ray diffraction analysis. The incorporation of PAC nanoparticles influences the structure and physicochemical properties as well as the transport and separation characteristics of the produced membranes. The applicability of the fabricated carbon-based membrane was tested in the filtration experiments. The fabricated membrane is characterized by a high NOM removal efficiency of 79% in the filtration process. Further modification of the membrane composition may result in a further increase in the efficiency of removing contaminants from water.
The paper reports the removal of phosphorus and natural organic matter (NOM) from surface water by dynamic membrane (DM) adsorber. DM filter builds up as a layer of particles deposited via permeation through the membrane’s surface. This study reports the application of Heated Aluminium Oxide Particles (HAOPs) as a dynamic membrane adsorber. Filtration experiments were conducted with surface water and batch tests were carried out with synthetic water. The efficiency of phosphorus removal along with the efficiency of organics (represented as UV-254) removal was evaluated. Additionally, the impact of HAOPs surface loading on the changes of transmembrane pressure (TMP), the kinetics, isotherm modeling of the adsorption and the effect of the pH, the effect of ionic strength, the effect of coexisting organic matter on phosphorus removal efficiency were studied. In the case of phosphorus removal in batch adsorption experiments, its sorption kinetic and isotherm data were analyzed using pseudo-first- and pseudo-second-order models and Langmuir and Freundlich models, respectively. The results indicated that Langmuir adsorption isotherm fits the experimental data best (0.9894). The kinetics of phosphorus adsorption on HAOPs was best described by the pseudo-second-order model and the best removal was achieved at the pH 6–7 (96.65% on average). An increase in ionic strength did not impact the efficiency of phosphorus removal significantly. The outcome of this study highlights HAOPs efficiency in NOM removal up to 92% in filtration experiments. In the case of phosphorous, removal efficiency varied. For the highest HAOPs dose, the degree of phosphorus removal ranged up to 93 ± 5%. The same removal efficiency was observed for the lowest dose while for 17 g/m2 of HAOPs the fluctuations were larger and varied from 64.7% to 92%. The results demonstrate that HAOPs could potentially be applied in the removal of phosphorus from surface water, especially when there is a high concentration of phosphorus in the water. However, this process requires further research and optimization of its parameters.