The historic Penouta mine in northwest Spain is the focus of efforts to extract tantalum from tin mining waste. This paper describes the characterisation of the tantalum mineralogy of waste material from the deposit. Characterisation was realised using quantitative mineralogy and geochemistry. This paper further identifies other phases of interest and investigates the potential for extraction using gravity separation techniques. The gravity concentrate obtained through these tests was analysed using quantitative mineralogy and electron probe microanalysis. Following characterisation of the sample material to identify the key Ta-bearing mineral phases and assess liberation, a series of gravity separation trials were conducted using Heavy Liquid Separation (HLS), Mozley table, Knelson concentrator separation and shaking table. The laboratory shaking table used to conduct a rougher test and a rougher/cleaner test to simulate a spiral-table circuit using the Penouta material. Mass balance calculations were carried out to calculate the contained metal content of the feed material and concentrate products in order to assess recovery rates for Ta, Sn and Nb across a range of grains sizes. Ta was found to be present predominantly in the solid-solution columbite-group mineral, along with minor Ta present as microlite and as impurities within cassiterite. It was found that over 70% of the Ta is contained within the −125 μm fraction, with the Ta-bearing minerals tantalite and microlite being closely associated with quartz. Mozley table separation resulted in recoveries of 89% Ta and 85% Nb for the −125 μm fraction. The Knelson Concentrator trial was carried out on the −625 μm size fraction, thereby eliminating low grade material found in the coarsest fractions. Size analysis of the recovery rate for each product, shows that the Knelson concentrator is most efficient for recovery of −125 μm particles.
As part of a study investigating the influence of mineralogical variability in a sediment hosted copper–cobalt deposit in the Democratic Republic of Congo on flotation performance, the flotation of nine sulphide ore samples was investigated through laboratory batch kinetics tests and quantitative mineral analyses. Using a range of ore samples from the same deposit the influence of mineralogy on flotation performance was studied. Characterisation of the samples through QEMSCAN showed that bornite, chalcopyrite, chalcocite and carrollite are the main copper-bearing sulphide minerals while carrollite is the only cobalt-bearing mineral. Mineralogical characteristics were averaged per sample to allow for a quantitative correlation with flotation performance parameters. Equilibrium recoveries, rate constants and final grades of the samples were correlated to the feed mineralogy through Multiple Linear Regression (MLR). Target sulphide minerals content and particle size, magnesiochlorite content, carrollite liberation and association of the copper and cobalt minerals with magnesiochlorite and dolomite were used to predict flotation performance. Leave One Out Cross Validation (LOOCV) revealed that the final copper and cobalt grades are predicted with an R2 of 0.80 and 0.93 and Root Mean Square Error of Cross Validation (RMSECV) of 4.41% and 1.34%. The recovery of cobalt and copper with time can be predicted with an R2 of 0.94 for both and an overall test error of 4.70% and 5.14%. Overall, it was shown that quantitative understanding of changes in mineralogy allows for prediction of changes in flotation performance.
Automated Scanning Electron Microscopy (ASEM) systems are applied in the mining industry to quantify the mineralogy of the ore feed and products. With society pushing towards sustainable mining, this quantification should be comprehensive and include trace minerals since they are often either deleterious or potential by-products. Systems like QEMSCAN® offer a mode for trace mineral analysis (TMS mode); However, it is unsuitable when all phases require analysis. Here, we investigate the potential of detecting micron-sized trace minerals in fieldscan mode using the QEMSCAN® system with analytical settings in line with the mining industry. For quality comparison, analysis was performed at a mining company and a research institution. This novel approach was done in full collaboration with both parties. Results show that the resolution of trace minerals at or below the scan resolution is difficult and not always reliable due to mixed X-ray signals. However, by modification of the species identification protocol (SIP), quantification is achievable, although verification by SEM-EDS is recommended. As an add-on to routine quantitative analysis focused on major ore minerals, this method can produce quantitative data and information on mineral association for trace minerals of precious and critical metals which may be potential by-products in a mining operation.
Loki’s Castle on the Arctic Mid-Ocean Ridge (AMOR) is an area of possible seafloor massive sulphide (SMS)-style mineralisation under Norwegian jurisdiction, which, due to mounting social pressure, may be a strategic future source of base and precious metals. The purpose of this study is to characterise mineralised material from a hydrothermal vent system on the AMOR in detail for the first time, and to discuss the suitability of methods used; reflected light microscopy, X-ray diffraction (XRD), whole rock geochemistry, electron probe micro-analysis (EPMA), and QEMSCAN. The primary sulphide phases, identifiable by microscopy, are pyrite and marcasite with minor pyrrhotite and galena, but multiple samples from the Loki’s Castle contain economically interesting quantities of copper (hosted in isocubanite and chalcopyrite) and zinc (hosted in sphalerite), as well as silver and gold. This reinforces the notion that slow spreading ridges may host significant base metal deposits. Micro-textures (chalcopyrite inclusions and exsolutions in sphalerite and isocubanite respectively) are typically undefinable by QEMSCAN, and require quantitative measurement by EPMA. QEMSCAN can be used to efficiently generate average grain size and mineral association data, as well as composition data, and is likely to be a powerful tool in assessing the effectiveness of SMS mineral processing.
Cobalt (Co) mine production primarily originates from the sediment-hosted copper (Cu) deposits of the Democratic Republic of Congo (DRC). These deposits usually consist of three ore zones with a supergene oxide ore blanket overlying a transition zone which grades into a sulphide zone at depth. Each of these zones display a mineral assemblage with varying gangue mineralogy and, most importantly, a distinct state of oxidation of the mineralisation. This has direct implications for Cu and Co extraction during mineral processing as it dictates which processing method is to be used (i.e., leaching vs. flotation) and affects the performance of these. To optimise resource efficiency, reduce technical risks and environmental impacts, comprehensive understanding of variation of ore mineralogy and texture in the deposit is essential. By defining geometallurgical ore types according to their inferred metallurgical behaviour, this information can serve to classify the resources and improve resource management. To obtain insight into the spatial distribution of mineral grades, it is necessary to develop techniques that have the potential to measure rapidly and, preferably, within the mine at relatively low-cost. In this study, the application of portable Fourier transformed infrared (FTIR) spectroscopy is investigated to measure the mineralogy of drill core samples. A set of samples from a sediment-hosted Cu-Co deposit in DRC was selected to test this approach. Results were validated using automated mineralogy (QEMSCAN). Prediction of gangue and target mineral grades from the FTIR spectra was achieved through partial least squares regression (PLS-R) combined with competitive adaptive reweighted sampling (CARS). It is shown that the modal mineralogy obtained from FTIR can be used to classify the ore according to type of mineralisation and gangue mineralogy into geometallurgical ore types. This classification supports selection of a suitable processing route and is likely to affect the overall process performance.