Maxillofacial prostheses are frequently made from silicone elastomer. The silicone material’s rough surface can lead to the accumulation of microorganisms, irritation of the surrounding soft tissue, and the progression of some microsites into mechanical failure and color deterioration. This in vitro study aimed to compare the surface roughness of M511 heat-vulcanized maxillofacial silicone before and after artificial aging. Eighty disk-shaped specimens were prepared and divided equally among five experimental groups based on pigmentation, with 16 samples in each group. The colorless specimens were prepared without adding any pigment. The four study groups were prepared using distinct pigments (red, blue, yellow, and their mixture). Half of the specimens in each group were tested before aging, while the other half was tested after 750 h of artificial aging. Surface roughness was measured using atomic force microscopy (AFM), and the silicone bonds and pigments were observed using Fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR). Data were compared between groups using a two-way analysis of variance, independent sample t-test, and Tukey’s post hoc test, considering a p < 0.05 statistically significant. FTIR-ATR showed no differences between the pre-and post-aging groups, with similar peaks observed. The surface roughness significantly increased in the colorless, blue, and mixed pigment groups (p < 0.001), surface roughness increased by 155.66%, 14.83%, and 96.12% respectively for colorless, blue pigment, and the mixture of pigments after 750 h of artificial aging. In contrast, the surface roughness significantly decreased in the yellow pigment (90.98%) and red pigment (5.7%) (p ≤ 0.001) after aging. The yellow pigment showed the smoothest surface after aging, while colorless specimens showed the roughest surface. Two-way ANOVA showed that pigment type and aging time significantly affected surface roughness. Therefore, induced aging considerably impacted the surface topography of maxillofacial silicone. The pigment type and distribution in the silicone matrix affected its surface roughness. The AFM analysis is a simple and straightforward method for assessing surface roughness at the nanometer level.
Background: Maxillofacial prostheses made of silicone elastomers tend to lose color. Despite advances in materials and processes, color change over time remains a challenge. Objective: This in vitro study aimed to observe how zirconium dioxide (ZrO2) nanoparticles impact the color stability of M511 heat temperature vulcanizing (HTV) silicone elastomer following outdoor weathering. Methods: ZrO2 nanoparticles were added in concentrations of 1%, 2%, and 3% by weight to the M511 HTV silicone elastomer. Brilliant red- and mocha-pigmented silicone pigments were utilized, along with colorless silicone as a base control. A total of 90 disk-shaped specimens were fabricated and divided into nine experimental groups, each containing ten samples (n = 10). All specimens were subjected to 6 months of outdoor weathering. A colorimeter was used to measure the values of L*a*b* according to the CIELab system. The 50:50% perceptibility threshold (∆E* = 1.1) and acceptability threshold (∆E* = 3.0) were used to interpret recorded color differences. At the 0.05 level of significance, the 1-way ANOVA and the Tukey post hoc test were used in the statistical analysis. Results: All evaluated specimen groups experienced a chromatic alteration (∆E* > 0). The ∆E* values exceeded the perceptible threshold in all groups (1.1 units). The ∆E* value of the colorless group and the red pigment with and without ZrO2 nanoparticles were both above the acceptable threshold (p < 0.001). Mocha control was also above the acceptable level but was not statistically significant (p > 0.99). ZrO2 nanoparticles showed a reduction in color change. Conclusion: According to this in vitro study, all specimens underwent color changes. Even colorless silicone exhibited a significant color change. The red pigment showed a highly significant chromatic alteration. ZrO2 nanoparticles showed important protection and a reduction in color change. Its protecting action increased with an increase in the concentration of ZrO2 nanoparticles (3% ZrO2 > 2% ZrO2 > 1% ZrO2).
5 May 2020 in Kurdistan Journal of Applied Research
In late 2019, a novel coronavirus appeared in Wuhan, Hubei province, China, and then rapidly spread around the world. The virus produces severe and even fatal pneumonia; the most common clinical symptoms among infected persons include fever, shortness of breath, cough, fatigue, and abnormal chest CT. Though the virus first traveled from animal to human, it can now spread from human to human through direct transmission such as coughing, sneezing, and inhalation of droplets; and through contact with mucus membranes of oral, nasal, and eye. COVID-19 also can be transmitted through saliva and the fecal–oral route. The risk of cross-infection between patients and dental practitioners is high due to the nature of dental work, so this outbreak has made a powerful impact, both medically and economically, on the dentistry sector. Dental practitioners should have comprehensive knowledge of the virus and its route of transmission, and they should take proper precautions during dental treatments to protect themselves and their patients. This article provides a review of COVID-19, its transmission routes, necessary precautions during dental setting, and the virus’s impact on the economy of the dental industry.
This study aimed to investigate the effect of time and different disinfecting agents on nanocomposite filler composed of natural clay nanoparticles (modified and non-modified) added to maxillofacial silicone elastomers and readymade pigment additives. A total of 360 disk-shaped samples were divided into nine pigment-based groups, each with four subgroups (n = 10) exposed to different disinfectants: distilled water, 1% sodium hypochlorite (NaOCl), 2% chlorhexidine (CHX), and effervescent tablets. Color changes (ΔE) were measured before and after disinfection using a colorimeter. The ΔE values were assessed against perceptibility (ΔE = 1.1) and acceptability (ΔE = 3) thresholds. Nanoclay additives were also characterized using FTIR, XRD and EDX. Statistical analysis, including ANOVA and post hoc HSD tests, revealed that while all samples exhibited some color change, most remained below the acceptability threshold. Colorless silicone showed minimal, non-significant change according to perceptibility threshold (ΔE = 1.1). Blue pigments displayed significant change only with effervescent tablets. Red and mixed pigments showed perceptible changes with NaOCl, CHX, and effervescent tablets. However, nanoclay-containing specimens showed no significant perceptible alterations. Overall, despite minor perceptible changes in some pigments, all disinfecting agents tested resulted in color differences below the acceptability threshold, indicating their safe use for disinfecting maxillofacial silicone materials without compromising esthetics. Nevertheless, nanoclays are more reliable agents for the pigmentation of maxillofacial silicone as they show non-significant chromatic alteration.