Recent research has highlighted the potential of honeybees and bee products as biological samplers for monitoring xenobiotic pollutants. However, the effectiveness of these biological samplers in tracking microplastics (MPs) has not yet been explored. This study evaluates several methods of sampling MPs, using honeybees, pollen, and a novel in-hive passive sampler named the APITrap. The collected samples were characterized using a stereomicroscopy to count and categorise MPs by morphology, colour, and type. To chemical identification, a micro-Fourier transform-infrared (FTIR) spectroscopy was employed to determine the polymer types. The study was conducted across four consecutive surveillance programmes, in five different apiaries in Denmark. Our findings indicated that APITrap demonstrated better reproducibility, with a lower variation in results of 39%, compared to 111% for honeybee samples and 97% for pollen samples. Furthermore, the use of APITrap has no negative impact on bees and can be easily applied in successive samplings. The average number of MPs detected in the four monitoring studies ranged from 39 to 67 in the APITrap, 6 to 9 in honeybee samples, and 6 to 11 in pollen samples. Fibres were the most frequently found, accounting for an average of 91% of the total MPs detected in the APITrap, and similar values for fragments (5%) and films (4%). The MPs were predominantly coloured black, blue, green and red. Spectroscopy analysis confirmed the presence of up to five different synthetic polymers. Polyethylene terephthalate (PET) was the most common in case of fibres and similarly to polypropylene (PP), polyethylene (PE), polyacrylonitrile (PAN) and polyamide (PA) in non fibrous MPs. This study, based on citizen science and supported by beekeepers, highlights the potential of MPs to accumulate in beehives. It also shows that the APITrap provides a highly reliable and comprehensive approach for sampling in large-scale monitoring studies.
This study investigates airborne microplastic (MP) pollution in Europe's largest greenhouse-based agricultural region. Despite the intensive use of plastics in this production system, evidence on airborne MP occurrence and spatial patterns remains scarce. Furthermore, this is particularly relevant in arid and semi-arid areas, where wind erosion and dust resuspension can enhance atmospheric transport. To achieve this, a portable active air-sampling device was developed and validated to accurately measure sampled air volume and provide comparable estimates of MP abundance (items/m3). The monitoring campaign covered environments strongly influenced by intensive agriculture (greenhouse interiors and surrounding areas), as well as urban zones and a protected natural area. MPs were detected in all air samples (n = 100 filter meshes) collected between February and October 2025. The concentration levels ranging from 8 to 59 items/m3. A clear land-use gradient was observed. The highest mean abundance was found inside greenhouses (31 items/m3), followed by urban air (28 items/m3) and greenhouse surroundings (23 items/m3), while the protected natural area showed the lowest levels (16 items/m3). Fibres were the dominant particle type in all environments (70-83%), and 31% of particles were < 100 µm, highlighting a potentially inhalable fraction. Polymer composition also varied by site: PET was predominant overall (46-69%), PE was relatively enriched inside greenhouses (27%), and PP was more common in urban samples (24%). Contamination factor analysis indicated mainly moderate to considerable pollution, with higher average contamination in greenhouse and urban areas than in the natural area. These findings provide baseline evidence for exposure assessment in plastic-intensive agricultural landscapes.
Microplastics (MPs) in water treatment plants (WTPs) represent a critical environmental concern, particularly when treated effluent is reused for agricultural irrigation. This study investigates the occurrence, removal efficiency, and characterization of MPs in tertiary-treated wastewater destined for agricultural reuse in water-scarce regions. Additionally, the study examines the influence of sample volume on extrapolated MP concentrations. Despite advanced treatment processes including ultrafiltration achieving removal efficiencies of 89%, substantial quantities of MPs remain in final effluents at concentrations ranging from 89 to 399 MPs/m3 (equivalent to 0.1–0.4 MPs/L) with a mass load of 2 µg/L at the outlet. Morphological analysis revealed a shift from fragment-dominated influent (~50%) to film-dominated effluent (~51%), with blue particles being most prevalent. Size distribution analysis showed distinct peaks: 50–100 µm for fragments, 100–250 µm for films, and 250–500 µm for fibres. Polytetrafluoroethylene (PTFE) emerged as the dominant polymer across all morphotypes. Finally, converting particle counts to mass loads indicated an average decrease from ~11 µg/L at the inlet to ~2 µg/L at the outlet, underscoring that number- and mass-based metrics provide complementary information for risk assessment.
Respiratory exposure to microplastics (MPs) remains poorly quantified because most tissue-based studies neither report extraction recovery efficiency nor assess whole-organ burden. Using lamb lungs as a model, we validated a method for determining MP burden in lung tissue by comparing three digestion oxidants and three sample masses against four spiked reference polymers:polypropylene(PP),polystyrene (PS),low-density polyethylene (LDPE) and polyethylene terephthalate (PET). Sodium persulfate (Na2S2O8) digestion of 10 g freeze-dried tissue (~25% of the lamb lung) gave the best recovery (~70%) and was applied to lung tissue from captive-held Saharan ungulates (two adult gazelles, a pregnant gazelle with two fetuses, and a neonatal aoudad). Across the adult gazelles, fibres dominated the internal burden, with PP enriched among fragments and PET dominant among fibres, confirmed by micro-Fourier- transform infrared spectroscopy (µFTIR). Particles were overwhelmingly coarse (mostly 30 to ≥100 µm), with essentially none meeting respirable (<10 µm) or alveolar-like (<4 µm) size criteria, consistent with retention in conducting airways rather than alveolar deposition. No MPs were detected in either fetus or in the neonatal aoudad, suggesting postnatal rather than prenatal accumulation of pulmonary burden. This is, to our knowledge, the first recovery-characterized, whole-lung (one animal) and per-gram tissue-level (two animals) burdens in captive-held ungulates, providing a transferable framework for assessing respiratory MP exposure in captive-held life and livestock.
Airborne microplastics (MPs) are emerging contaminants of concern in school environments, where children may experience prolonged exposure. This study assessed airborne MPs at three Spanish schools located in contrasting settings: a dense urban area in Madrid (A), a residential area in Almería (B), and an agricultural peri-urban area in Almería surrounded by greenhouses (C). An additional simultaneous indoor–outdoor comparison was performed at School B. Air samples were collected using active samplers with 25 µm stainless-steel meshes, and particles were characterised by stereomicroscopy, µ-FTIR spectroscopy, FESEM, and FTIR. Fibres were the predominant morphology, and polyethylene terephthalate (PET) was the most abundant synthetic polymer. School A showed the highest abundance of synthetic fibres, while polymer composition differed significantly among schools (χ2 (12) =41.77, p < 0.0001). Indoor samples contained more particles than outdoor samples, although natural-to-synthetic proportions were similar; PP, PA, and PE contributed relatively more indoors, whereas PET predominated outdoors. Only 0.45% and 0.13% of particles fell within the <10 µm and <4 µm estimated aerodynamic-size ranges, respectively, all being fibres. Overall, airborne MP occurrence varied with location and indoor–outdoor setting, while selected PET and PP fibres showed polymer-dependent surface and chemical alteration.