Dominik Schroeder

Mr. Dominik Schroeder

orcid

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 August 2025 in Energies
Verified
Journal Article
Open access
PDF file
ŁBŁukasz Brodzik
Łukasz Brodzik
Bartosz CiupekBartosz Ciupek
Bartosz Ciupek
AFAndrzej Frąckowiak
Andrzej Frąckowiak
DSDominik Schroeder
Dominik Schroeder
This study investigated the thermomechanical behaviour of the nozzle of a GTM 400MOD miniature turbojet engine during combustion of aviation kerosene and co-combustion of kerosene with hydrogen. Numerical analysis was based on experiments conducted on a dedicated test rig at engine speeds ranging from 31,630 rpm to 65,830 rpm, providing data on the temperature and dynamic pressure at the nozzle outlet. These data served as input to numerical analyses using the ANSYS Fluent, Steady-State Thermal, and Static Structural modules to evaluate exhaust gas flow, temperature distribution, and stress and strain states. The paper performed a basic analysis with additional simplifications, and an extended analysis that took into account, among other things, thermal radiation in the flow. The results of the basic analysis show that, at comparable thrust levels, co-firing and pure kerosene combustion yield similar nozzle temperature distributions, with maximum wall temperatures ranging from 978 K to 1090 K, which remain below the allowable limit of 1193 K (920 °C). Maximum stresses reached approximately 261 MPa, close to but not exceeding the yield strength of 316 stainless steel. Maximum nozzle deformation did not exceed 0.8 mm. Small dynamic pressure fluctuations were observed; For example, at 31,630 rpm, co-firing increased the maximum dynamic pressure from 1.56 × 104 Pa to 1.63 × 104 Pa, while at 47,110 rpm, it decreased from 4.05 × 104 Pa to 3.89 × 104 Pa. The extended analysis yielded similar values for the nozzle temperature and pressure distributions. Stress and strain increased by more than 76% and 78%, respectively, compared to the baseline analysis. The results confirm that hydrogen co-firing does not significantly alter the nozzle thermomechanical loads, suggesting that this emission-free fuel can be used without negatively impacting the nozzle’s structural integrity under the tested conditions. The methodology, combining targeted experimental measurements with coupled CFD and FEM simulations, provides a reliable framework for assessing material safety margins in alternative fuel applications in small turbojet engines.

11 February 2026 in Energies
Verified
Journal Article
Open access
PDF file
ŁBŁukasz Brodzik
Łukasz Brodzik
Bartosz CiupekBartosz Ciupek
Bartosz Ciupek
Grigore CicanGrigore Cican
Grigore Cican
ŁSŁUKASZ SEMKŁO
ŁUKASZ SEMKŁO
DSDominik Schroeder
Dominik Schroeder
Research related to the use of hydrogen is crucial because it can be a significant factor in reducing exhaust emissions into the environment. This work represents the second stage of research related to the analysis of exhaust gases from a miniature GTM 400 MOD turbojet engine. Based on the parameters obtained in the experiment, a numerical study of the flow downstream of the exhaust nozzle was performed in ANSYS software (version R1, 2025). The main goal of the calculations was to obtain the temperature distribution and compare the values at checkpoints where actual measurements were taken. The study was conducted in two stages. In the first stage, the engine operated conventionally, burning kerosene. In the second stage, co-combustion of kerosene and hydrogen occurred in the engine. The numerical analysis enabled the visualization of the flow phenomenon for these stages within the considered rotational speeds. The analysis examined flow in domains where the gap was included and excluded. This gap was created by the different diameters of the container opening and the engine nozzle outlet. The study showed that ignoring the gap allows for temperatures closer to the experimental values. Results deemed satisfactory were less likely to be found in vortex areas, but more likely in areas closer to the container walls and the engine exhaust stream itself. The results of the conducted tests showed that the Root Mean Square Error RMSE was within the range of 9.5–22.8% relative to the average temperature values obtained from experimental measurements. The highest turbulence intensity occurred for hydrogen co-combustion at a higher rotational speed, reaching 284% for Variant 2 and 300% for Variant 1. The largest standard deviation for both fuel types at a distance of 0.083 m from the container wall was 68.5 K for variant 2 and 76 K for variant 1. At a distance of 0.166 m from the container wall, the deviation was 76 K for variant 2 and 83.8 K for variant 1.