Adverse climate change has forced a deeper reflection on the scale of pollution related to human activity, including in the aviation industry. As a result, fundamental questions have arisen about the characteristics of these pollutants, the mechanisms of their formation and potential strategies for reducing them. This paper provides a comprehensive overview of key technical solutions to minimize the environmental impact of aircraft engines. The solutions presented range from fuel innovations to advanced design changes and drive concepts. Particular attention was paid to sustainable aviation fuels (SAFs), which are currently an important element of the environmental strategy regulated by the European Union. It also discusses the potential use of hydrogen as a potential alternative fuel to replace traditional aviation fuels in the long term. The analysis in the article made it possible to characterize in detail possible modifications in the functioning of aircraft engines, based both on the current state of technical knowledge and on the anticipated directions of its development, which has not been a frequent issue in comprehensive research so far. The analysis shows that the type of raw material used to create SAF has a strong impact on its physical and chemical parameters and the degree of greenhouse gas emissions. This necessitates a broader analysis of the legitimacy of using a given type of fuel from the SAF group in the direction of selected air operations and areas with a higher risk of severe atmospheric pollution. These results provide the basis for further research into sustainable solutions in the aviation sector that can contribute to significantly reducing its impact on climate change.
6 December 2014 in Inverse Problems in Science and Engineering
In this study, the Cauchy problem for the Laplace equation in a multiply connected region was solved. Solving this problem was replaced by solving the Poisson equation in a simply connected region with an unknown source function different from zero in the adjoined region. To determine the power of the sources, a convergent iterative process has been developed based on polyharmonic functions, including the tests on the effect of the polyharmonic function order on the solution accuracy.
2 January 2018 in International Journal of Numerical Methods for Heat & Fluid Flow
Purpose: This paper aims to present the Cauchy problem for the Laplace’s equation for profiles of gas turbine blades with one and three cooling channels. The distribution of heat transfer coefficient and temperature on the outer boundary of the blade are known. On this basis, the temperature on inner surfaces of the blade (the walls of cooling channels) is determined. Design/methodology/approach: Such posed inverse problem was solved using the finite element method in the domain of the discrete Fourier transform (DFT). Findings: Calculations indicate that the regularization in the domain of the DFT enables obtaining a stable solution to the inverse problem. In the example under consideration, problems with reconstruction constant temperature, assumed on the outer boundary of the blade, in the vicinity of the trailing and leading edges occurred. Originality/value: The application of DFT in connection with regularization is an original achievement presented in this study.
13 May 2019 in International Journal of Numerical Methods for Heat & Fluid Flow
Purpose: T-shaped cavities occur by design in many technical applications. An example of such a stator cavity is the side space between the guide vane carriers and the outer casing of a steam turbine. Thermal conditions inside it have a significant impact on the deformation of the turbine casing. In order to improve its prediction, the purpose of this paper is to provide a methodology to gain better knowledge of the local heat transfer at the cavity boundaries based on experimental results. Design/methodology/approach: To determine the heat transfer coefficient distribution inside a model cavity with the help of a scaled generic test rig, an inverse heat conduction problem is posed and a method for solving such type of problems in the form of linear combinations of Trefftz functions is presented. Findings: The results of the calculations are compared with another inverse method using first-order gradient optimization technique as well as with estimated values obtained with an analytic two-dimensional thermal network model, and they show an excellent agreement. The calculation procedure is proved to be numerically stable for different degrees of complexity of the sought boundary conditions. Originality/value: This paper provides a universal and robust methodology for the fast direct determination of an arbitrary distribution of heat transfer coefficients based on material temperature measurements spread over the confining wall.
This paper focuses on the analysis of the gas flow in the axisymmetric mini gap bounded by the surface of the top of the labyrinth seal tooth and the surface of the body. It includes the results of experimental research and numerical calculations. Experimental research focused on the analysis of gas flow for six clearance heights in a wide range of pressure drops. Based on this research, we determined the mass flow in the clearance. Using the Saint-Venant equation, we determined the flow coefficient versus the pressure ratio upstream and downstream from the seal. Flow coefficients for various clearance heights obtained from the experiment can be divided into two data groups, the values of which differ significantly. To explain changes in the value of the gas flow coefficient for selected clearance heights, numerical analysis of the said gas flow was performed using the Fluent software. This analysis allowed us to explain the reason for the variability of the flow coefficient. This research can be the basis for determining the change of seal integrity during operation for staggered and stepped seals.
This article presents an overview of thermal calculation methods used in boilers powered by fossil fuels (solid, liquid or gas). The analysis was carried out mainly in terms of combustion chamber calculation methods. Changing standards and legal regulations regarding the use of fossil fuels in Europe and the world make it necessary to adapt calculation methods and boiler design to current requirements, and many of them are related to outdated boiler models or for fuels that are no longer so heavily used in industrial solutions. Current research and development trends implemented in the EU and in the world related to the issues of the European Green Deal, the Fit for 55 directive and other ecological trends in the energy sector make it necessary to verify and remodel the calculation methods used so far in terms of the thermal efficiency of the device, fuel consumption or the use of fuels not previously used in their wide range in a wider application. Hence, the knowledge and updating of the state of knowledge in the field of the thermal calculation of boilers in terms of their environmental performance is necessary and strongly sought after by researchers. It is undoubted that in the next few years, boilers will continue to be the main source of thermal energy, especially in the power industry or industry. A reasonable energy transition should be based on the direction of the thermal optimization of already functioning structures and adaptation of their operating parameters to the planned new ecological fuels in the sense of the intensification of energy converted from primary form to thermal energy, and in the last step, it should reorganize the energy and industrial sectors, leaving only these groups of devices treated as a stable and necessary source of energy. Therefore, it should be recognized that activities aimed at improving the thermal parameters of boilers should directly improve the thermal efficiency of the device, and this will translate into fuel savings and reduce their negative impact on the environment.