The purpose of this study is to support eco-design ideas and sustainable manufacturing techniques by examining the energy consumption related to drilling holes for different furniture connections. The experimental model is a simple piece of furniture made from birch plywood with three different types of joints. Eccentric joints, confirmat screws, and dowel measurements of energy consumption with a CNC drilling and milling machine show different values for every kind of connector. The energy consumption was measured using a portable power quality analyzer, specifically the PQ-box 150 manufactured by A:Eberle GmbH & Co. KG Nürnberg, Germany. This device likely adheres to industry standards for energy measurement, ensuring accurate and reliable results. The measurement process involved recording energy consumption at different stages of the machining process, allowing for the analysis of specific cutting work and total energy consumption for various joint types. Dowels exhibit the lowest energy consumption at 0.105 Wh for one furniture joint, confirmat screws at 0.127 Wh, while eccentric joints, despite their higher energy consumption (0.173 Wh), offer enhanced transportability and assembly flexibility of a piece of furniture. Specific cutting power for one selected piece of furniture was 227.89 J/mm³ for dowels, 190.63 J/mm³ for eccentric joints and 261.68 J/mm³ for confirmat screws.

This study investigates the screw withdrawal resistance (SWR) of hollow wood–plastic composite (WPC) door frames, which serve as moisture-resistant alternatives to traditional wood-based materials. The tested WPC, characterised by a density of 1.33 g/cm³ and a polymer-bound lignocellulosic filler, exhibits superior dimensional stability and low water absorption—under 4% after 24 h of immersion. The research focuses on how the unique chambered geometry of these industrial profiles affects the anchoring of 20 mm conical wood screws used to mount essential fittings such as hinges and lock catches. The SWR was determined using a universal testing machine in accordance with the modified EN 320 standards. Results indicate that the installation location within the profile significantly dictates load-bearing capacity: the band profile (lock catch) achieved an average SWR of 525.65 N, while the beam profile (hinge) averaged only 275.25 N. This performance gap arises because screws anchor only into internal “ribs” rather than the full material depth. Since these values are considerably lower than those of traditional particleboard (~1364–1775 N), the study highlights a critical need to optimise screw dimensions to ensure the structural stability and safety of hollow WPC door systems.

Global particleboard production reached almost 123 million m³ in 2024. Such quantities require intensified search for alternative lignocellulosic materials in accordance with the principles of the circular economy. The research aim was to determine the total energy consumption (E_max) and specific cutting work (SCW) when drilling holes in boards made from 100% forest biomass, agricultural biomass, and wood-based post-production residues. The experiments were carried out on a CNC (computerize numerical control) center at a constant speed of 6000 rpm and variable feed rates of 0.2, 2, and 20 mm/min, using conventional particleboard as a reference. The results showed that the feed rate has a dominant influence on energy consumption. As the speed increased, the average SCW value decreased from 22.32 J/mm³ to 6.11 J/mm³. Conventional board required the highest energy input in all variants, and statistical analyses showed no significant differences (p > 0.05) between boards made from alternative raw materials and the reference. This proves that the variability of energy consumption depends mainly on the process parameters and not on the material itself. The research confirms the technological feasibility of using alternative biomass sources in the furniture industry without increasing energy consumption during processing, which promotes the implementation of sustainable development principles.

The research aimed to determine the strength and stiffness of corner joints in interior door frames, depending on their construction and the modifications made to the design of the door frame joints. Initially, two models were compared: model 1, with two connectors using a clamping screw at an angle of 45°, and model 0, with a single connector using a cam joint at an angle of 90°. In all tests, model 1 exhibited significantly better mechanical properties. To improve the performance of model 0, three alternative construction models (A, B, and C) were proposed by changing the position of the door frame mounting holes. In the compression test, model A showed an increased bending moment compared to model 0, while models B and C showed no such improvement. In the tension test, the bending moment values remained at a similar level across all construction variants, including model 0. In terms of bending moment, the best result in compression was achieved by model A (48.26 Nm), and in tension by model B (48.72 Nm). The highest stiffness was demonstrated by model 1 (up to 42.38 kNm/rad), while among the alternative models, model C showed the best result in tension (33.98 kNm/rad). Due to the favourable increase in bending moment under compression in model A and the insignificant changes under tension across all variants, model A is considered the optimal solution. To enhance the strength of the door frame, offset holes can be applied as proposed in this model.