María Castillo-García

Dr. María Castillo-García


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2016 in Physica Medica
Verified
Journal Article
Closed access
ARA. Rodríguez-Ruiz
A. Rodríguez-Ruiz
MCMaría Castillo-García
María Castillo-García
JGJ. Garayoa
J. Garayoa
MCM. Chevalier
M. Chevalier

15 August 2017 in European Radiology
Verified
Journal Article
Closed access
PDF file
JGJulia Garayoa
Julia Garayoa
MCMARGARITA CHEVALIER CHEVALIER
MARGARITA CHEVALIER CHEVALIER
MCMaría Castillo-García
María Castillo-García
IMIgnacio Mahíllo-Fernández
Ignacio Mahíllo-Fernández
NONajim Amallal El Ouahabi
Najim Amallal El Ouahabi
JVJulio Valverde
Julio Valverde

1 July 2017 in Academic Radiology
Verified
Journal Article
Closed access
MCMaría Castillo-García
María Castillo-García
MCMargarita Chevalier
Margarita Chevalier
JGJulia Garayoa
Julia Garayoa
ARAlejandro Rodriguez-Ruiz
Alejandro Rodriguez-Ruiz
DPDiego García Pinto
Diego García Pinto
JVJulio Valverde
Julio Valverde

31 March 2026 in Polymers
Verified
Journal Article
Open access
PDF file
Thomas HofmannThomas Hofmann
Thomas Hofmann
MBMartin Buschmann
Martin Buschmann
ABAdrián Belarra
Adrián Belarra
MCMaría Castillo-García
María Castillo-García
MCMARGARITA CHEVALIER CHEVALIER
MARGARITA CHEVALIER CHEVALIER
PHPeter Homolka
Peter Homolka
Additive manufacturing enables the rapid fabrication of radiographic phantoms for X-ray and CT imaging, supporting applications such as patient simulation, dosimetry, imaging protocol optimization, and quality assurance. Polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS) are among the most widely used printing polymers in phantoms; however, their X-ray attenuation properties can vary substantially among manufacturers, product lines within manufacturers, and even between colors of the same product. Cylindrical samples of 34 PLA filaments from 11 manufacturers and 13 ABS filaments from 9 manufacturers were evaluated for X-ray attenuation and energy dependence between 70 and 140 kV using a clinical CT scanner. Measured mass densities ranged from 1.17 to 1.34 g/cm3 for PLA and 1.03–1.11 g/cm3 for ABS. At 120 kV, Hounsfield unit (HU) values spanned 109 to 424 HU for PLA and −34 to 40 HU for ABS. Energy dependence, quantified as the HU at 70 kV minus HU at 140 kV, ranged from −29 to +172 HU for PLA filaments and −52 to −4 HU for ABS filaments. Identical products differing only in color showed HU variations from 90 HU at 120 kV, with no consistent pattern linking specific colors to highest or lowest attenuation. These findings demonstrate that 3D printing materials require individual characterization, as base polymer designation alone does not predict X-ray behavior accurately. The observed variability, however, enables the design of phantoms with tailored attenuation and energy-dependent contrast. Referring only to base polymers when specifying 3D printing materials for radiographic phantoms or suggesting printing materials as radiographic substitutes to mimic a specified tissue or reference material without naming the actual product, including color, is, thus, insufficient.

1 September 2016 in Physica Medica
Verified
Journal Article
Closed access
ARA. Rodríguez-Ruiz
A. Rodríguez-Ruiz
MCMaría Castillo-García
María Castillo-García
JGJ. Garayoa
J. Garayoa
MCM. Chevalier
M. Chevalier

1 January 2015 in Revista de Senología y Patología Mamaria
Verified
Journal Article
Closed access
MCMaría Castillo-García
María Castillo-García
JGJulia Garayoa
Julia Garayoa
CECarmen Estrada
Carmen Estrada
ATAlejandro Tejerina
Alejandro Tejerina
OBOlivia Benitez
Olivia Benitez
MCMargarita Chevalier
Margarita Chevalier