Thomas Hofmann

Mr. Thomas Hofmann


Research Focus & Metrics

Academic Career Length

1Year (2026-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 March 2026 in Biomimetics
Verified
Journal Article
Open access
PDF file
Thomas HofmannThomas Hofmann
Thomas Hofmann
MBMartin Buschmann
Martin Buschmann
PHPeter Homolka
Peter Homolka
Background: Phantoms are essential in medical imaging, providing reproducible and quantitative means for system and protocol evaluation, image quality assessment, and dosimetry without patient exposure. Additive manufacturing enables rapid, accurate fabrication of phantoms ranging from simple geometries to complex anthropomorphic models. Ongoing developments in 3D printing technologies and polymer formulations have enhanced mechanical properties and printability, but also affect X-ray attenuation behaviour, necessitating an update with current materials to facilitate the choice of appropriate materials mimicking body tissues in radiographic phantoms. Methods: Attenuation properties of 27 photopolymer resins and 22 thermoplastic filaments (based on PLA, ABS, HIPS, PETG/PCTG, and PVB) were quantified using a clinical CT scanner at 70–140 kV to establish reference data for material selection. Results: At 120 kV, resins exhibited attenuation values between 124 and 384 Hounsfield Units (HU), and filaments ranged from −69 to 308 HU (PLA-based filaments: 160 to 241 HU, ABS: −32 to 43 HU, PETG/PCTG: 151 to 308 HU, and HIPS: −69 to −22 HU). Energy dependence of HU values is presented from 70 to 140 kV tube potential. Compared to the 2021 study, a wider selection of X-ray opacities is available. Regarding SLA/DLP printing, resins with higher attenuation were identified, and flexible resins that had provided a choice of low attenuation printing materials in the range of 60 to 90 HU at 120 kV tended to replicate attenuation properties closer to rigid photopolymers; i.e., HU values were slightly higher. In FDM filaments, a wide variation in different PLA-, ABS-, and HIPS-based filaments is found. In copolymers from the PET/PCTG/PETG family, very inhomogeneous X-ray attenuations are still found, as anticipated. Conclusions: The range of X-ray attenuation observed demonstrates that commercially available 3D printing materials can replicate clinically relevant tissues and tissue-equivalent contrasts. Furthermore, the available range of attenuations has increased, as has the finer gradation of these materials. These findings support the design of patient- and task-specific imaging phantoms for optimization of acquisition protocols, image quality evaluation, and radiation dose studies, as well as facilitate the selection of appropriate phantom materials.

31 March 2026 in Polymers
Verified
Journal Article
Open access
PDF file
Thomas HofmannThomas Hofmann
Thomas Hofmann
MBMartin Buschmann
Martin Buschmann
ABAdrián Belarra
Adrián Belarra
MCMaría Castillo-García
María Castillo-García
MCMARGARITA CHEVALIER CHEVALIER
MARGARITA CHEVALIER CHEVALIER
PHPeter Homolka
Peter Homolka
Additive manufacturing enables the rapid fabrication of radiographic phantoms for X-ray and CT imaging, supporting applications such as patient simulation, dosimetry, imaging protocol optimization, and quality assurance. Polylactic acid (PLA) and acrylonitrile butadiene styrene (ABS) are among the most widely used printing polymers in phantoms; however, their X-ray attenuation properties can vary substantially among manufacturers, product lines within manufacturers, and even between colors of the same product. Cylindrical samples of 34 PLA filaments from 11 manufacturers and 13 ABS filaments from 9 manufacturers were evaluated for X-ray attenuation and energy dependence between 70 and 140 kV using a clinical CT scanner. Measured mass densities ranged from 1.17 to 1.34 g/cm3 for PLA and 1.03–1.11 g/cm3 for ABS. At 120 kV, Hounsfield unit (HU) values spanned 109 to 424 HU for PLA and −34 to 40 HU for ABS. Energy dependence, quantified as the HU at 70 kV minus HU at 140 kV, ranged from −29 to +172 HU for PLA filaments and −52 to −4 HU for ABS filaments. Identical products differing only in color showed HU variations from 90 HU at 120 kV, with no consistent pattern linking specific colors to highest or lowest attenuation. These findings demonstrate that 3D printing materials require individual characterization, as base polymer designation alone does not predict X-ray behavior accurately. The observed variability, however, enables the design of phantoms with tailored attenuation and energy-dependent contrast. Referring only to base polymers when specifying 3D printing materials for radiographic phantoms or suggesting printing materials as radiographic substitutes to mimic a specified tissue or reference material without naming the actual product, including color, is, thus, insufficient.