Jihua Shang

Dr. Jihua Shang


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
27 April 2020 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
JSJihua Shang
Jihua Shang
XYXinyu Yang
Xinyu Yang
JSJihua Shang
Jihua Shang
MHMengyuan Hu
Mengyuan Hu
CHCuiliu Han
Cuiliu Han
JZJiuxing Zhang
Jiuxing Zhang
The porous tungsten matrixes of barium tungsten cathodes are prepared by spark plasma sintering (SPS). By adjusting the raw powder particle diameter and the porosity, the matrixes with different average distances between the pores are obtained. The microstructure and the emission performance of the barium tungsten cathode are analyzed using scanning electron microscopy (SEM), electron emission measurement system, and X-ray photoelectron spectroscopy (XPS). The average distances between the pores of three cathodes are 5.08, 5.74, and 6.91μm, respectively. The cathode with a distance of 5.74,μ m has the best zero-field current density and the lowest work function. With the increase in the pulsewidth, the variation rate of the current density for the 5.74-μm cathode is the smallest, indicating the emission stability is the best. The best emission performance can be ascribed to the formation of the optimal Ba-O dipoles' coverage on the cathode surface.

30 December 2020 in IEEE Electron Device Letters
Verified
Journal Article
Closed access
JSJihua Shang
Jihua Shang
XYXinyu Yang
Xinyu Yang
ZWZiyu Wang
Ziyu Wang
JSJiali Shi
Jiali Shi
JZJiuxing Zhang
Jiuxing Zhang
A barium tungsten (Ba-W) cathode was successfully prepared with spherical W powder in this paper, and the porous matrix exhibited homogeneous pore distribution and good inter-pore connectivity. In the space charge limited zone, the cathode with spherical powder (Sph cathode) showed higher current density compared with the cathode with conventional powder. The practical work function distribution (PWFD) of Sph cathode was only 0.063 eV, which demonstrated this cathode had better emission uniformity. Ba coverage rate at pore ends made larger impact to the uniformity of work function distribution than the diffusion distance of Ba on the cathode surface.

7 July 2021 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
JWJ. L. Wang
J. L. Wang
JSJihua Shang
Jihua Shang
YGYuanjun Guo
Yuanjun Guo
YJY. Y. Jiang
Y. Y. Jiang
WXW. K. Xiong
W. K. Xiong
XZXiaotao Zu
Xiaotao Zu

9 March 2022 in IEEE Transactions on Plasma Science
Verified
Journal Article
Closed access
JSJihua Shang
Jihua Shang
XYXinyu Yang
Xinyu Yang
DSDapeng Sun
Dapeng Sun
ZWZiyu Wang
Ziyu Wang
XXXiong Xu
Xiong Xu
JZJiuxing Zhang
Jiuxing Zhang
An electron beam heating model capable of heating terahertz (THz) cathode has been developed. The cathode temperature field was simulated, which showed that both the heat radiation of the THz heater and the electron beam bombardment made contribution to heating the THz cathode. Experimentally, the emission capacity of the THz heater made of tungsten-thorium filament was investigated at different temperatures. The dependences of the cathode temperature on the bombardment power $P$ or the THz heater temperature $T_{h}$ were studied, respectively. The cathode temperature can reach 1098 °C at $P$ of 3.98 W and $T_{h}$ of 1725 °C. The warm-up time of the THz cathode was investigated, and the cathode temperature became stable at 1100 °C in 27 s.

1 January 2022 in Acta Physica Sinica
Verified
Journal Article
Closed access
PDF file
JSJihua Shang
Jihua Shang
XYXinyu Yang
Xinyu Yang
DSDa-Peng Sun
Da-Peng Sun
JZJiu-Xing Zhang
Jiu-Xing Zhang
分别从基体和铝酸盐两方面优化了钡钨阴极. 在基体方面, 首先采用窄粒度钨粉结合放电等离子体烧结获得了孔径分布窄的基体; 再利用射频等离子体球化技术制备了球形钨粉, 采用球形钨粉制备了多孔基体, 获得了孔通道光滑、内孔连通性好、孔径分布更加窄的基体. 与窄粒度钨粉基体相比, 球形钨粉制备的阴极, 空间电荷限制区的斜率由1.25增加至1.37, 发射均匀性得到提高, 拐点电流密度由6.6 A·cm–2增至6.96 A·cm–2. 在此基础上, 采用液相法改善了铝酸盐物相组成, 发现空间电荷限制区的斜率增加至1.44, 拐点电流密度增加至21.2 A·cm–2. 通过理论计算对钡钨阴极发射的物理本质进行了研究, 发现钡钨阴极发射规律遵循偶极子理论.

29 April 2026 in Applied Sciences
Verified
Journal Article
Open access
PDF file
JSJihua Shang
Jihua Shang
HXHouxiu Xiao
Houxiu Xiao
ZWZeyuan Wang
Zeyuan Wang
DLDandan Liang
Dandan Liang
SFShizhu Fan
Shizhu Fan
LLLuwei Liu
Luwei Liu
Transmission electron microscopy (TEM) is an essential technique for characterizing nanomaterials. However, specimen preparation, which is a critical factor affecting image quality, remains a practical challenge. Focusing on nanopowders used in materials and chemical science, this article employs case studies to analyze the key steps in TEM specimen preparation. Carbon support films (CSFs) are essential tools for specimen preparation, and this study introduces several commonly used, cost-effective options, including conventional CSFs, conventional holey CSFs, ultrathin holey CSFs, and double-grid support films. We characterize their structural and morphological characteristics and evaluate their suitability for different types of samples. Several representative case studies of nanopowders, spanning from zero-dimensional (0D) to one-dimensional (1D) and two-dimensional (2D) materials, are used to illustrate tailored specimen preparation approaches, which serve as practical references for researchers conducting TEM characterization. These findings facilitate higher image reliability and experimental efficiency, thereby providing critical support for advancing fundamental exploration and frontier innovation in nanomaterial science.